Bedienungsanleitung Makita BTD145 (Seite 7 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

598618

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

• After inserting the bit, make sure that it is firmly

secured. If it comes out, do not use it.

Hook (Fig. 11)

The hook is convenient for temporarily hanging the tool.

This can be installed on either side of the tool.

To install the hook, insert it into a groove in the tool hous-

ing on either side and then secure it with a screw. To

remove, loosen the screw and then take it out.

OPERATION

The proper fastening torque may differ depending upon

the kind or size of the screw/bolt, the material of the

workpiece to be fastened, etc. The relation between fas-

tening torque and fastening time is shown in the figures.

(Fig. 12, 13 & 14)

Hold the tool firmly and place the point of the driver bit in

the screw head. Apply forward pressure to the tool to the

extent that the bit will not slip off the screw and turn the

tool on to start operation.

NOTE:

• Use the proper bit for the head of the screw/bolt that

you wish to use.

• When fastening screw M8 or smaller, choose a proper

hammer force, and carefully adjust pressure on the

switch trigger so that the screw is not damaged.

• Hold the tool pointed straight at the screw.

• If the hammering force is too strong you tighten the

screw for a time longer than shown in the figures, the

screw or the point of the driver bit may be overstressed,

stripped, damaged, etc. Before starting your job,

always perform a test operation to determine the

proper fastening time for your screw.

The fastening torque is affected by a wide variety of fac-

tors including the following. After fastening, always check

the torque with a torque wrench.

1. When the battery cartridge is discharged almost

completely, voltage will drop and the fastening

torque will be reduced.

2. Driver bit or socket bit

Failure to use the correct size driver bit or socket bit

will cause a reduction in the fastening torque.

3. Bolt

• Even though the torque coefficient and the class of

bolt are the same, the proper fastening torque will

differ according to the diameter of bolt.

• Even though the diameters of bolts are the same,

the proper fastening torque will differ according to

the torque coefficient, the class of bolt and the bolt

length.

4. The manner of holding the tool or the material of

driving position to be fastened will affect the torque.

5. Operating the tool at low speed will cause a reduc-

tion in the fastening torque.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspec-

tion or maintenance except for the following troubleshooting related to the light.

Cleaning

From time to time wipe off the outside (tool body) of the tool using a cloth dampened in soapy water.

CAUTION:

• Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.

Troubleshooting

To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by

Makita Authorized Service Centers, always using Makita replacement parts.

Trouble Light status/LED indicator status/tool status Steps to be taken

The tool

stops during

operation.

LED indicator for empty signal for remaining

battery capacity lights up.

Remaining battery capacity level is low. Charge the

battery cartridge.

When the LED indicator still lights up even after

charging the battery cartridge, the tool temperature is

high. Cool down it fully. The tool restarts after its

temperature becomes low.

When the status is still unchanged, stop using and

have the tool repaired by a Makita local service

center.

Light flickers once per second.

The tool temperature is high. Cool down it fully. The

tool restarts after its temperature becomes low.

Light flickers five times per second.

Use the tool with the motor not locked. (When the

tool has stopped due to the motor locking, withdraw

the battery cartridge one time and then insert it again

or release the switch trigger for more than

60 seconds to restart the tool.)

If the motor still remains locked, stop using and have

the tool repaired by a Makita local service center.

Switch trigger has been pulled continuously

for more than 130 seconds.

Release the switch trigger.

Other Symptoms

Stop using and have the tool repaired by a Makita

local service center.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BTD145 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info