Bedienungsanleitung Makita BTW151 (Seite 5 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

600708

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

5. Hold the tool firmly.

6. Always be sure you have a firm footing.

7. Be sure no one is below when using the tool in high

locations.

8. The proper fastening torque may differ depending

upon the kind or size of the bolt. Check the torque

with a torque wrench.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing battery cartridge (Fig. 1)

•

Always switch off the tool before insertion or removal of the

battery cartridge.

•

To remove the battery cartridge, withdraw it from the tool

while sliding the button on the side of the cartridge.

•

To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip it

into place. Always insert it all the way until it locks in place

with a little click. If you can see the red part on the upper

side of the button, it is not locked completely. Insert it fully

until the red part cannot be seen. If not, it may accidentally

fall out of the tool, causing injury to you or someone around

you.

•

Do not use force when inserting the battery cartridge. If the

cartridge does not slide in easily, it is not being inserted

correctly.

Charging (Fig. 2)

1. Plug the battery charger into the proper A/C voltage source. Two charging lights will flash in green color repeatedly.

2. Insert the battery cartridge into charger until it stops adjusting to the guide of charger. Terminal cover of charger can be

opened with inserting and closed with pulling out the battery cartridge.

3. When the battery cartridge is inserted, the charging light color will change from green to red and charging will begin. The

charging light will keep lighting up lit steadily during charging.

One red charging light indicates charged condition in 0 – 80% and two red ones indicates 80 – 100%.

4. With finish of charge, the charging lights will change from two red ones to two green ones.

5. If you leave the battery cartridge in the charger after the charging cycle is complete, the charger will switch into its ‘‘trickle

charge (maintenance charge)’’ mode which will last approximately 24 hours.

6. After charging, unplug the charger from the power source. Refer to the table below for the charging time.

Battery type Capacity (mAh) Number of cells Charging time

BH1420 2,000 12 Approx. 30 min.

BH1433 3,300 12 Approx. 50 min.

NOTE:

•

The battery charger is for charging Makita-battery cartridge.

Never use it for other purposes or for other manufacturer’s

batteries.

•

When you charge a new battery cartridge or a battery

cartridge which has not been used for a long period of time,

it may not accept a full charge. This is a normal condition

and does not indicate a problem. You can recharge the

battery cartridge fully after discharging it completely and

recharging a couple of times.

•

If you charge a battery cartridge from a just-operated tool or

battery cartridge which has been left in a location exposed

to direct sunlight for a long time, the charging light may flash

in red color. If this occurs, wait for a while. Charging will

begin after the battery cartridge is cooled by the cooling fan

installed in the charger. When the temperature on battery is

more than approx. 70°C, two charging lights may flash in

red color, and when approx. 50°C – 70°C, one charging light

in red color.

•

If the charging light flashes alternately in green and red

color, charging is not possible. The terminals on the charger

or battery cartridge are clogged with dust or the battery

cartridge is worn out or damaged.

Cooling system

•

This charger is equipped with cooling fan for heated battery

in order to enable the battery to prove its own performance.

Sound of cooling air comes out during cooling, which means

no trouble on the charger.

•

Yellow light will flash for warning in the following cases.

– Trouble on cooling fan

– Incomplete cool down of battery, such as, being clogged

with dust

The battery can be charged in spite of the yellow warning

light. But the charging time will be longer than usual in this

case.

Check the sound of cooling fan, vent on the charger and

battery, which can be sometime clogged with dust.

•

The cooling system is in order although no sound of cooling

fan comes out, if the yellow warning light will not flash.

•

Always keep clean the vent on charger and battery for

cooling.

•

The products should be sent to repair or maintenance, if the

yellow warning light will frequently flash.

Conditioning charge

Conditioning charge can extend the life of battery by automati-

cally searching the optimum charging condition for the batter-

ies in every situation.

The battery employed in the following conditions repeatedly,

will be worn out shortly, and yellow warning light may flash.

1. Recharge of battery with its high temperature

2. Recharge of battery with its low temperature

3. Recharge of full charged battery

4. Over-discharge of battery (continue to discharge battery

in spite of down of power.)

5. Recharge under broken cooling system

The charging time of such battery is longer than usual.

Makita BTW151 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info