Bedienungsanleitung Makita BTW151 (Seite 6 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

600708

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Trickle charge (Maintenance charge)

If you leave the battery cartridge in the charger to prevent

spontaneous discharging after full charge, the charger will

switch into its ‘‘trickle charge (maintenance charge)’’ mode

and keep the battery cartridge fresh and fully charged.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely dis-

charged.

Always stop tool operation and charge the battery car-

tridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room temperature at

10°C – 40°C (50°F – 104°F).

Let a hot battery cartridge cool down by inserting it into the

charger.

4. Charge the Nickel Metal Hydride battery cartridge when

you do not use it for more than six months.

Selecting correct socket

Always use the correct size socket for bolts and nuts. An

incorrect size socket will result in inaccurate and inconsistent

fastening torque and/or damage to the bolt or nut.

Installing or removing socket (Fig. 3 & 4)

CAUTION:

Always be sure that the tool is switched off and the battery

cartridge is removed before installing or removing the socket.

1. For socket without O-ring and pin

To install the socket, push it onto the anvil of the tool until

it locks into place.

To remove the socket, simply pull it off.

2. For socket with O-ring and pin

Move the O-ring out of the groove in the socket and

remove the pin from the socket. Fit the socket onto the

anvil of the tool so that the hole in the socket is aligned

with the hole in the anvil. Insert the pin through the hole in

the socket and anvil. Then return the O-ring to the original

position in the socket groove to retain the pin. To remove

the socket, follow the installation procedures in reverse.

Switch action (Fig. 5)

CAUTION:

Before inserting the battery cartridge into the tool, always

check to see that the switch trigger actuates properly and

returns to the ‘‘OFF’’ position when released.

To start the tool, simply pull the trigger. Tool speed is

increased by increasing pressure on the trigger. Release the

trigger to stop.

Reversing switch action (Fig. 6)

CAUTION:

•

Always check the direction of rotation before operation.

•

Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation before the

tool stops may damage the tool.

•

When not operating the tool, always set the reversing switch

lever to the neutral position.

This tool has a reversing switch to change the direction of

rotation. Depress the reversing switch lever from the A side for

clockwise rotation or from the B side for counterclockwise

rotation. When the reversing switch lever is in the neutral

position, the switch trigger cannot be pulled.

Auto-stop setting for number of impacts (Fig. 7)

This tool has a convenient auto-stop mechanism that allows you to preset the desired number of impacts in terms of the

application. The tool then stops automatically after reaching the preset number of impacts.

1. To set the dial on the back of the tool, first slide out the battery cartridge by sliding the button on the side of the cartridge.

2. Two dials can be seen on the battery holder side. Use a slotted screwdriver to set the dial to a desired 2-digit setting.

3. You cannot set the auto-stop setting for fastening with more than 200 impacts (over 4 sec.)

Note:

Do not force the dial when turning. You might break it.

Dial setting and function (Fig. 7)

Bolt fastening

Dial setting Clockwise Counterclockwise Application

01–98

Tool stops after the twice the

set number of impacts is

reached. See the next sec-

tion for the appropriate fas-

tening torque.

Pull the trigger to start the

tool; release it to stop.

Bolt fastening while control-

ling the number of impacts.

Pull the trigger to start the tool; release it to stop. Bolt fastening without con-

trolling the number of

impacts; or when fastening

with more than 200 impacts

(over 4 sec.)

No rotation even with trigger

pulled.

Pull the trigger to start the

tool; release it to stop.

—

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BTW151 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info