Bedienungsanleitung Makita BUC121 (Seite 13 von 84) (Deutsch, Englisch)

476839

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

When a poor chain oil delivery occurs at the top of

guide bar, clean the filter as follows.

Remove the battery cartridge from the tool.

Remove the sprocket cover and saw chain from the tool.

(Refer to the section titled " Installing or removing saw

chain ".)

Fig.22

Remove the push nut using a slotted bit screwdriver with

a slender shaft or the like.

Fig.23

Take the filter out of the chain saw and remove small

dust or particles from it. When the filter is too dirty,

replace it with a new one.

Insert the battery cartridge into the tool.

Fig.24

Pull the switch trigger to flow built-up dust or particles off

the oil discharge hole by discharging chain oil.

Remove the battery cartridge from the tool.

Fig.25

Insert the cleaned oil filter into the oil discharge hole.

When the filter is too dirty, replace it with a new one.

Fig.26

Insert the push nut with its correct side facing up as

shown in the figure into the oil discharge hole to secure

the filter. When the filter cannot be secured with a

disfigured push nut, replace the push nut with a new

one.

Reinstall the sprocket cover and saw chain on the tool.

Replacing the sprocket

Before fitting a new saw chain, check the condition of the

sprocket.

Fig.27

CAUTION:

• A worn sprocket will damage a new saw chain.

Have the sprocket replaced in this case. The

sprocket need to be installed so that it always

faces as shown in the figure.

Fig.28

Always fit a new locking ring when replacing the

sprocket.

Replacing carbon brushes

Fig.29

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps.

Take out the worn carbon brushes, insert the new ones

and secure the brush holder caps.

Fig.30

Storing tool

Clean the tool before storing. Remove any chips and

sawdust from the tool after removing the sprocket cover.

After cleaning the tool, run it under no load to lubricate

the saw chain and guide bar.

Cover the guide bar with the scabbard.

Remove oil from the oil tank to empty it and place the

chain saw with the tank cap facing upward.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers,

always using Makita replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are

recommended for use with your Makita tool

specified in this manual. The use of any other

accessories or attachments might present a risk of

injury to persons. Only use accessory or

attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Various type of Makita genuine batteries and

chargers

• Saw chain

• Scabbard

• Guide bar complete

• File

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BUC121 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info