Bedienungsanleitung Makita CA5000 (Seite 7 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691238

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

7ENGLISH

4. Always observe that the guard is covering the

blade before placing saw down on bench or

oor. An unprotected, coasting blade will cause

the saw to walk backwards, cutting whatever is in

its path. Be aware of the time it takes for the blade

to stop after switch is released.

Additional safety warnings

1. Use extra caution when cutting damp wood,

pressure treated lumber, or wood containing

knots. Maintain smooth advancement of tool with-

out decrease in blade speed to avoid overheating

the blade tips.

2. Do not attempt to remove cut material when

blade is moving. Wait until blade stops before

grasping cut material. Blades coast after turn off.

3. Avoid cutting nails. Inspect for and remove all

nails from lumber before cutting.

4. Place the wider portion of the saw base on

that part of the workpiece which is solidly

supported, not on the section that will fall off

when the cut is made. If the workpiece is short

or small, clamp it down. DO NOT TRY TO HOLD

SHORT PIECES BY HAND!

►Fig.5

5. Before setting the tool down after completing a

cut, be sure that the guard has closed and the

blade has come to a complete stop.

6. Never attempt to saw with the circular saw

held upside down in a vise. This is extremely

dangerous and can lead to serious accidents.

►Fig.6

7. Some material contains chemicals which may

be toxic. Take caution to prevent dust inhala-

tion and skin contact. Follow material supplier

safety data.

8. Do not stop the blades by lateral pressure on

the saw blade.

9. Do not use any abrasive wheels.

10. Only use the saw blade with the diameter that

is marked on the tool or specied in the man-

ual. Use of an incorrectly sized blade may affect

the proper guarding of the blade or guard opera-

tionwhichcouldresultinseriouspersonalinjury.

11. Keep blade sharp and clean. Gum and wood

pitch hardened on blades slows saw and

increases potential for kickback. Keep blade clean

byrstremovingitfromtool,thencleaningitwith

gum and pitch remover, hot water or kerosene.

Never use gasoline.

12. Wear a dust mask and hearing protection when

use the tool.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and unplugged before adjusting or

checking function on the tool.

Quick stop for 3, 4, or 6 mm board

thickness groove cutting

By turning the quick stop, you can choose the appro-

priate depth of groove cutting for 3, 4, or 6 mm board

thickness swiftly.

The number, seen from the handle side, indicates the

workpiece board thickness.

Forneadjustmentofdepthofgroove,usethedepth

adjustingknob.

►Fig.7: 1.Quickstop  2.Depthadjustingknob

0 mm depth is set properly when the tool is shipped

from the factory, but if you changed the depth of groove

bytheadjustingknob,renethe0mmdepthasfollows:

1. Turn the quick stop to 0 mm.

2. Turnthedepthadjustingknobtoadjustthedepth.

3. Make sure that the blade does not make any

contact with work piece.

4. Holdthetoolrmlywithonehandonthefrontgrip

and the other on the tool handle. Push in the lock-off

button, and turn the tool on.

5. Slowly press down the saw head fully, and check

whether the groove cutter blade does not contacts but

almost touches the workpiece. If not, stop the tool and

wait until the groove cutter blade stops completely, and

adjustthedepthbyturningthedepthadjustingknob

again.

Adjusting depth of cut

Toadjustdepthofcut,turnthedepthadjustingknob.

For deeper cut, turn it clockwise. For shallower cut, turn

it counterclockwise.

►Fig.8: 1.Depthadjustingknob

Sighting

Triangular mark on the base indicates the center of the

groove cutter blade.

When using with groove cutter blade, align the outside

triangular mark with the cutting line.

►Fig.9: 1. Base 2. Outside triangular mark

3. Inside triangular mark 4. Cutting line

Switch action

CAUTION: Before plugging in the tool, always

check to see that the switch trigger actuates

properly and returns to the "OFF" position when

released.

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided.

To start the tool, push in the lock-off button and pull the

switch trigger.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita CA5000 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info