Bedienungsanleitung Makita CA5000 (Seite 8 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691238

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

8 ENGLISH

Release the switch trigger to stop.

►Fig.10: 1. Lock-off button 2. Switch trigger

Speed adjusting dial

CAUTION: The speed adjusting dial is not for

using low speed rated blades but for obtaining a

speed which is suitable to material of workpiece.

Use only blades which are rated for at least the maxi-

mum no load speed stated in the SPECIFICATIONS.

CAUTION:Thespeedadjustingdialcanbeturned

only as far as 6 and back to 1. Do not force it past

6 or 1, or the speed adjusting function may no

longer work.

Thetoolspeedcanbeadjustedbyturningtheadjusting

dial. Higher speed is obtained when the dial is turned in

the direction of number 6; lower speed is obtained when

it is turned in the direction of number 1.

Refer to the table to select the proper speed for the

workpiece to be cut. However, the appropriate speed

may differ with the type or thickness of the workpiece. In

general, higher speeds will allow you to cut workpieces

faster but the service life of the blade will be reduced.

Number min

-1

1 2,000

2 2,500

3 3,500

4 4,500

5 5,500

6 6,400

►Fig.11: 1.Speedadjustingdial

Guide plate

For aligning the guide rail (optional accessory) with the

cutting line, use the guide plate.

►Fig.12: 1. Guide plate 2. Plate edge 3. Cutting

line

1. Set the guide plate onto the guide rail near from

the cutting start point. The plate edge represents the

center of the groove cutter blade. Align the plate edge

with the cutting line.

2. Then, set again the guide plate on the guide rail

near the cutting end point. And align the plate edge with

the cutting line again.

Other features

The tools equipped with electronic function are easy to

operate because of the following features.

Overload protector

When the load on the tool exceeds admissible levels,

power to the motor is reduced to protect the motor from

overheating. When the load returns to admissible lev-

els, the tool will operate as normal.

Constant speed control

Electronic speed control for obtaining constant speed.

Possibletogetnenish,becausetherotatingspeedis

kept constant even under load condition.

Soft start feature

Soft start because of suppressed starting shock.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and unplugged before carrying out

any work on the tool.

Hex wrench storage

Hex wrench is stored on the tool. To remove hex

wrench,justpullitout.

To install hex wrench, place it on the grip and insert it as

far as it goes.

►Fig.13: 1. Hex wrench

Removing or installing groove

cutter blade

CAUTION: Do not use blades which do not

comply with the characteristics specied in these

instructions.

CAUTION: Use only blades which are rated for

at least the maximum no load speed stated in the

SPECIFICATIONS.

CAUTION: Be sure the blade is installed with

teeth pointing up at the front of the tool.

CAUTION: Use only the Makita wrench to

install or remove the blade.

To remove the groove cutter blade, perform following

steps:

1. Lie down the tool as the motor housing and the

base touching the ground. Then insert the hex wrench

into the hex hole, push it in, and open the blade case

door by turning the hex wrench.

►Fig.14

2. Press the shaft lock fully so that the blade does

not revolve, then loosen the hex bolt counterclockwise

with the wrench.

►Fig.15: 1. Shaft lock 2. Hex bolt

3. Removethehexbolt,outerangeandblade.

►Fig.16: 1.Hexbolt  2.Outerange  3.Groove

cutterblade  4.Innerange

To install the blade, follow the removal procedure in

reverse. Be sure to tighten the hex bolt clockwise

securely. And close the blade case door after installing

the blade.

When changing blade, make sure to also clean the

guard of accumulated sawdust and chips as discussed

in the Maintenance section. Such efforts do not replace

the need to check guard operation before each use.

Connecting a vacuum cleaner

For groove cutting operation, connect a Makita vacuum

cleaner to your tool.

Connect a hose of the vacuum cleaner to the dust port.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita CA5000 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info