Bedienungsanleitung Makita CG100D (Seite 8 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691771

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

8 ENGLISH

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge. Failure to hold the tool and the battery

cartridgermlymaycausethemtoslipoffyourhands

and result in damage to the tool and battery cartridge

andapersonalinjury.

►Fig.1: 1. Red indicator 2. Button 3. Battery cartridge

Toremovethebatterycartridge,slideitfromthetool

while sliding the button on the front of the cartridge.

Toinstallthebatterycartridge,alignthetongueonthe

battery cartridge with the groove in the housing and slip

itintoplace.Insertitallthewayuntilitlocksinplace

withalittleclick.Ifyoucanseetheredindicatoronthe

upper side of the button, it is not locked completely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen.Ifnot,

itmayaccidentallyfalloutofthetool,causinginjuryto

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly.Ifthecartridgedoesnotslideineasily,itis

not being inserted correctly.

Battery protection system

Thetoolisequippedwithabatteryprotectionsystem.

Thissystemautomaticallycutsoffpowertothemotorto

extend battery life.

Thetoolwillautomaticallystopduringoperationifthe

tool and/or battery are placed under one of the following

conditions:

Overloaded:

Thetoolisoperatedinamannerthatcausesittodraw

an abnormally high current.

Inthissituation,turnthetooloffandstoptheapplication

thatcausedthetooltobecomeoverloaded.Thenturn

the tool on to restart.

Ifthetooldoesnotstart,thebatteryisoverheated.In

this situation, let the battery cool before turning the tool

on again.

Low battery voltage:

Theremainingbatterycapacityistoolowandthetool

willnotoperate.Ifyouturnthetoolon,themotorruns

againbutstopssoon.Inthissituation,removeand

recharge the battery.

Indicating the remaining battery

capacity

Only for battery cartridges with the indicator

►Fig.2: 1.Indicatorlamps2. Check button

Press the check button on the battery cartridge to indi-

catetheremainingbatterycapacity.Theindicatorlamps

light up for a few seconds.

Indicator lamps Remaining

capacity

Lighted Off

75%to100%

50%to75%

25%to50%

0%to25%

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may differ slightly

from the actual capacity.

Switch action

WARNING: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

►Fig.3: 1. Switch trigger 2.Trigger-lockbutton

Topreventtheswitchtriggerfromaccidentallypulled,

the trigger-lock button is provided.

Tostartthetool,depressthetrigger-lockbuttonfromA

sideandpulltheswitchtrigger.Toolspeedisincreased

by increasing pressure on the switch trigger. Release

the switch trigger to stop.

After use, press in the trigger-lock button from B side.

Speed adjusting dial

►Fig.4: 1.Speedadjustingdial

Thetoolspeedcanbeadjustedbyturningthespeed

adjustingdial.Youcangetthehighestspeedat5and

the lowest speed at 1.

NOTICE: Do not turn the dial quickly when the

tool is working.

NOTICE: Depending on the type and conditions

of caulking material, it may not be fed at low

speed. In this case, set the speed adjusting dial

higher.

NOTICE: When changing the speed dial from "5"

to "1", turn the dial counterclockwise. Do not turn

the dial clockwise forcibly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita CG100D Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info