Bedienungsanleitung Makita CL104D (Seite 9 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

600673

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Charging the built-in battery

CAUTION:

• Do not operate the cleaner during charging. It may be

damaged.

• Always disconnect the charging plug from the cleaner

after charging.

• When you charge a new cleaner or a cleaner which

has been left uncharged for a long time, it may not

accept a full charge. This is a normal condition and

does not indicate a problem. You can recharge the

cleaner fully after discharging it completely a couple of

times.

Use only the Makita charger DC1001 to charge this

cleaner. Use of the other type chargers may cause the

battery to burst, result in personal injury and damage.

Charge the cleaner when using it for the first time or

uncharged for a long time. Connect the charging plug to

the charging connector, then plug in the charger to the

power receptacle. The battery power lamp lights up and

start charging. Charging takes approximately 3 hours. The

light goes out after the charging is complete. For more

details, refer to the instruction manual of battery charger.

(Fig. 1 & 2)

Switch action

CAUTION:

• Always be sure that the dust bag or paper pack is

installed properly in the cleaner before use. Improper

installation may allow dust to enter the motor, resulting

in malfunction of the cleaner.

• Always switch off the cleaner after each use to prevent

damage to the cleaner and to extend the service life of

the batteries.

To start the cleaner, simply press the “1/2/3” button. To

switch off, press the “0” button. To change the cleaner

speed, press the “1/2/3” button. The first press on this

button is for high speed and the second press for low

speed. Each press on this button repeats the high/low

speed cycle alternatively.

While pressing the “1/2/3” button, this cleaner works with

turbo. This mode is appropriate to clean especially dusty

area. (Fig. 3)

Battery power lamp (Fig. 2)

When the remaining battery capacity gets low, the battery

power lamp blinks.

When the remaining battery capacity gets much lower, the

tool stops and the battery power lamp lights up about

10 seconds. At this time, charge the cleaner.

NOTE:

• The time at which the battery power lamp start blinking

or lighting up depends on the temperature at work

place and the battery cartridge conditions.

ASSEMBLY

Disposing of Dust

CAUTION:

• Empty the cleaner before it becomes too full, or the

suction force weakens.

• Be sure to empty out the dust inside the cleaner itself.

Failure to do so may cause the sponge filter to be

clogged or the motor to be damaged.

• Never throw away the dust stopper because it should

be used whenever either the dust bag or the dust pack

is used.

1. Push the button to open the front cover. Opening it

until a click is heard allows a positive stop at that

position. (Fig. 4)

CAUTION:

• When closing the front cover, be careful not to pinch

your fingers.

NOTE:

• The front cover comes off when trying to open the front

cover more than 90°. If the front cover comes off, install

it into the front cover joint in place. (Fig. 5)

2. Pull out both the orange-colored dust stopper and dust

bag together at the same time. (Fig. 6)

3. Remove the dust stopper and empty the cleaner.

(Fig. 7 & 8)

Dust bag and paper pack

Install either dust bag or paper pack before using cleaner.

Use the dust stopper when installing either dust bag or

paper pack.

Dust bag are usable many times repeatedly by cleaning it

out.

Paper pack is a throw-away type. Throw away the entire

paper pack without emptying when it has become full.

Installing dust bag (Fig. 9)

Use the dust stopper when installing dust bag. Be careful

not to take the upper side for the lower side by mistake

because they are different each other.

1. Insert the protrusion of the dust bag into the groove in

the dust stopper as shown in the figure. (Fig. 10)

2. There is no distinction between the upper and lower

sides of the dust bag. You may insert its protrusion of

any side into the lower groove of the dust stopper.

(Fig. 11)

3. Overlap the frame of dust stopper with that of the dust

bag. (Fig. 12)

4. Place the dust stopper and the dust bag together into

the cleaner cavity in the same direction of arrow on

the dust stopper. Insert them all the way into the slots

in the cleaner cavity. (Fig. 13)

5. Place the entire cloth part of the dust bag inside the

tool itself. (Fig. 14)

6. Close the front cover completely. (Fig. 15)

Installing the paper pack

1. Unfold the entrance of the paper pack before setting it

on the dust stopper. (Fig. 16)

Use the dust stopper also when installing dust pack. Be

careful not to take the upper side for the lower side by

mistake because they are different each other. (Fig. 9)

2. Insert the protrusion of the dust pack into the groove in

the dust stopper as shown in the figure. (Fig. 17)

3. There is no distinction between the upper and lower

sides of the dust pack. You may insert its protrusion of

any side into the lower groove of the dust stopper.

(Fig. 11)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita CL104D Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info