Bedienungsanleitung Makita DBM 131 (Seite 7 von 61) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch)

78789

Zoom out

Zoom in

Vorherige Seite

1/61

Nächste Seite

Technical Characteristics

Rated voltage: 110 V

Rated power input: 1500 W

Load speed: 1

speed 0 - 800 min

-1

speed 0 - 1570 min

-1

maximum drilling capacity:

speed 132 mm

speed 70 mm

Protection class: II

Collet: M 18

Weight(net): 6.8 kg

Collar clamping diameter: 53 mm

This machine is meant for professional use only!

All rights of changes due to technical development reserved.

Safety Instructions

Read and obey these instructions before using this machine.

ADDITIONAL SAFETY RULES FOR THIS MACHINE

1. This core-drill must only be used under constant supervision. Unplug and make sure the mains

switch is OFF whenever core-drill is not in use or left unattended, before servicing, adjustments,

change of cutter or other accessories and when there is a voltage drop (below 200V)

2. Only grip by insulated part of auxiliary handle and other plastic surfaces when performing drilling

where cutter is likely to contact hidden electrical wiring or its own cable. Contact with a “Live”

wiring will make all exposed metal surfaces of the machine “Live” and danger for an electric

shock.

3. Do not use the machine if a defect is found on the plug, mains lead, trigger switch or any part of

housings (daily inspection). Have them repaired by a qualified person.

4. For longer machine use, wear hearing protectors.

5. Machine should never be damp or wet. Do not use the machine in damp or wet locations.

6. Likewise it is recommended to wear safety helmet, safety glasses and/or face shield. Also wear

a dust mask and thickly padded gloves.

7. Prior to work starting, make sure that cutting accessory is fitted properly.

8. Before starting work carefully check all screws for tightness. Due to vibration screws come

loose and can cause serious breakdown or injury.

9. Make sure no one is below when using the machine in high locations.

10. Keep hands well away from rotating parts.

11. During machine operation, cooling water must never be allowed to enter motor or other electrical

installation.

12. Should there be any leaking of water between synthetic ring and gearbox, stop immediately and

have the fault rectified by an authorised service workshop.

13. Overhead (upward) drilling can only be carried out with the use of suitable protection shielding

(water collecting device).

14. After interrupt cutting, do not switch on the motor again unless core bit can rotate freely.

15. Avoid touching near dry-cut immediately after work process. Area can be very hot and cause

severe burns.

16. To avoid machine self-starting, always trigger-off the switch should power supply become

interrupted or plug accidentally withdrawn from the socket while motor is still running.

17. When coring manually, always use also auxiliary handle (side handle) and hold the machine

firmly with both hands.

18. Keep sure-footing and body balance at all times for better control of reaction torque.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DBM 131 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info