Bedienungsanleitung Makita DCS551 (Seite 4 von 64) (Deutsch, Englisch, Polnisch)

600550

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

23.10.2014

000331

Yasushi Fukaya

Director

Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

GEA010-1

General Power Tool Safety

Warnings

WARNING Read all safety warnings and all

instructions.

Failure to follow the warnings and instructions

may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for

future reference.

GEB058-4

CORDLESS METAL CUTTER

SAFETY WARNINGS

Cutting procedures

DANGER: Keep hands away from cutting

area and the blade. Keep your second hand

on auxiliary handle, or motor housing. If both

hands are holding the tool, they cannot be cut by

blade.

2. Do not reach underneath the workpiece. The

guard cannot protect you from the blade below

the workpiece.

3. Adjust the cutting depth to the thickness of

the workpiece. Less than a full tooth of the blade

teeth should be visible below the workpiece.

4. Never hold piece being cut in your hands or

across your leg. Secure the workpiece to a

stable platform. It is important to support the

work properly to minimize body exposure, blade

binding, or loss of control.

5. Hold the power tool by insulated gripping

surfaces only, when performing an operation

where the cutting tool may contact hidden

wiring. Contact with a "live" wire will also make

exposed metal parts of the power tool "live" and

could give the operator an electric shock.

6. When ripping, always use a rip fence or

straight edge guide. This improves the accuracy

of cut and reduces the chance of blade binding.

Always use blades with correct size and shape

(diamond versus round) of arbour holes.

Blades

that do not match the mounting hardware of the tool

will run eccentrically, causing loss of control.

8. Never use damaged or incorrect blade

washers or bolt. The blade washers and bolt

were specially designed for your tool, for optimum

performance and safety of operation.

Kickback causes and related warnings

− Kickback is a sudden reaction to a pinched, bound or

misaligned blade, causing an uncontrolled tool to lift

up and out of the workpiece toward the operator.

− When the blade is pinched or bound tightly by the kerf

closing down, the blade stalls and the motor reaction

drives the unit rapidly back toward the operator.

− If the blade becomes twisted or misaligned in the cut,

the teeth at the back edge of the blade can dig into the

top surface of the workpiece causing the blade to climb

out of the kerf and jump back toward the operator.

Kickback is the result of tool misuse and/or incorrect

operating procedures or conditions and can be avoided

by taking proper precautions as given below.

9. Maintain a firm grip with both hands on the

tool and position your arms to resist kickback

forces. Position your body to either side of

the blade, but not in line with the blade.

Kickback could cause the tool to jump backwards,

but kickback forces can be controlled by the

operator, if proper precautions are taken.

10.

When blade is binding, or when interrupting a cut

for any reason, release the trigger and hold the tool

motionless in the material until the blade comes to

a complete stop. Never attempt to remove the tool

from the work or pull the tool backward while the

blade is in motion or KICKBACK may occur.

Investigate and take corrective actions to eliminate the

cause of blade binding.

11. When restarting a tool in the workpiece,

center the blade in the kerf and check that

blade teeth are not engaged into the material.

If blade is binding, it may walk up or kickback

from the workpiece as the tool is restarted.

12.

Support large panels to minimise the risk of blade

pinching and kickback.

Large panels tend to sag

under their own weight. Supports must be placed under

the panel on both sides, near the line of cut and near

the edge of the panel.

13.

Do not use dull or damaged blades.

Unsharpened or

improperly set blades produce narrow kerf causing

excessive friction, blade binding and kickback.

14. Blade depth and bevel adjusting locking

levers must be tight and secure before

making cut. If blade adjustment shifts while

cutting, it may cause binding and kickback.

15.

Use extra caution when making a "plunge cut" into

existing walls or other blind areas.

The protruding

blade may cut objects that can cause kickback. For

plunge cuts, retract lower guard using retracting handle.

Lower guard function

16.

Check lower guard for proper closing before each

use. Do not operate the tool if lower guard does not

move freely and close instantly. Never clamp or tie

the lower guard into the open position.

If tool is

accidentally dropped, lower guard may be bent. Raise

the lower guard with the retracting lever and make sure

it moves freely and does not touch the blade or any

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DCS551 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info