Bedienungsanleitung Makita DCS551 (Seite 6 von 64) (Deutsch, Englisch, Polnisch)

600550

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before adjusting or

checking function on the tool.

Installing or removing battery cartridge

Fig.1

CAUTION:

• Always switch off the tool before installing or

removing of the battery cartridge.

• Hold the tool and the battery cartridge firmly

when installing or removing battery cartridge.

Failure to hold the tool and the battery cartridge

firmly may cause them to slip off your hands and

result in damage to the tool and battery cartridge

and a personal injury.

To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator on the

upper side of the button, it is not locked completely.

CAUTION:

• Always install the battery cartridge fully until the

red indicator cannot be seen. If not, it may

accidentally fall out of the tool, causing injury to

you or someone around you.

• Do not install the battery cartridge forcibly. If the

cartridge does not slide in easily, it is not being

inserted correctly.

Indicating the remaining battery capacity

(Only for battery cartridges with "B" at the end of the

model number.)

Fig.2

Press the check button on the battery cartridge to

indicate the remaining battery capacity. The indicator

lamps light up for few seconds.

Off

BlinkingLighted

Indicator lamps

Charge the

battery.

0% to 25%

25% to 50%

50% to 75%

75% to 100%

Remaining

capacity

The battery

may have

malfunctioned.

015658

NOTE:

• Depending on the conditions of use and the

ambient temperature, the indication may differ

slightly from the actual capacity.

Switch action

WARNING:

• For your safety, this tool is equipped with lock-off

lever which prevents the tool from unintended

starting. NEVER use the tool if it runs when you

simply pull the switch trigger without pressing the

lock-off lever. Return tool to a MAKITA service

center for proper repairs BEFORE further usage.

• NEVER tape down or defeat purpose and function

of lock-off lever.

CAUTION:

• Before installing the battery cartridge into the tool,

always check to see that the switch trigger

actuates properly and returns to the "OFF"

position when released.

• Do not pull the switch trigger hard without pressing

the lock-off lever. This can cause switch breakage.

Fig.3

To prevent the switch trigger from being accidentally

pulled, a lock-off lever is provided. To start the tool,

press the lock-off lever and pull the switch trigger.

Release the switch trigger to stop.

Indicating remaining battery capacity

(Country specific)

Fig.4

When you turn the tool on, the battery indicator shows

the remaining battery capacity.

The remaining battery capacity is shown as the

following table.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DCS551 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info