Bedienungsanleitung Makita DCS551 (Seite 7 von 64) (Deutsch, Englisch, Polnisch)

600550

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Battery indicator status

Remaining battery capacity

50% - 100%

20% - 50%

0% - 20%

Charge the battery

On Off

Blinking

015624

Automatic speed change function

Fig.5

Mode indicator status Operation mode

High speed mode

High torque mode

015137

This tool has "high speed mode" and "high torque

mode". It automatically changes operation mode

depending on the work load. When mode indicator lights

up during operation, the tool is in high torque mode.

Tool / battery protection system

The tool is equipped with a tool/battery protection

system. This system automatically cuts off power to the

motor to extend tool and battery life.

The tool will automatically stop during operation if the

tool or battery are placed under one of the following

conditions. In some conditions, the indicator lights up.

Overload protection

When the tool is operated in a manner that causes it to

draw an abnormally high current, the tool automatically

stops without any indications. In this situation, turn the

tool off and stop the application that caused the tool to

become overloaded. Then turn the tool on to restart.

Overheat protection for tool

When the tool is overheated, the tool stops

automatically and the battery indicator shows following

state. In this situation, let the tool cool before turning the

tool on again.

Battery indicator

Tool is overheated

On Off Blinking

015625

Releasing protection lock

When the protection system works repeatedly, the tool

is locked and the battery indicator shows the following

state.

Battery indicator

On Off Blinking

Protection lock works

015626

In this situation, the tool does not start even if turning

the tool off and on. To release the protection lock,

remove the battery, set it to the battery charger and wait

until the charging finishes.

Adjusting depth of cut

Fig.6

CAUTION:

• After adjusting the depth of cut, always tighten the

lever securely.

Loosen the lever on the side of the rear handle and

move the base up or down. At the desired depth of cut,

secure the base by tightening the lever.

For cleaner, safer cuts, set cut depth so that no more

than one blade tooth projects below workpiece. Using

proper cut depth helps to reduce potential for dangerous

KICKBACKS which can cause personal injury.

Sighting

Fig.7

Place the alignment line of the base on your intended

cutting line on the workpiece.

Lighting the lamp

CAUTION:

• Do not look in the lamp or see the source of light

directly.

Fig.8

Only to turn on the lamp, pull the switch trigger without

pressing the lock-off lever. To turn on the lamp and run

the tool, press the lock-off lever and pull the switch

trigger with the lock-off lever being pressed. The lamp

keeps on lighting while the switch trigger is being pulled.

The lamp goes out 10 -15 seconds after releasing the

trigger.

NOTE:

• Use a cotton stick to wipe the dirt off the lens of

lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

• Do not use gasoline, thinner or the like to clean

the lens of lamp. Using such substances will

damage the lens.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DCS551 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info