Bedienungsanleitung Makita DCS551 (Seite 8 von 64) (Deutsch, Englisch, Polnisch)

600550

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out

any work on the tool.

Removing or installing blade

CAUTION:

• Be sure the blade is installed with teeth pointing

up at the front of the tool.

• Use only the Makita wrench to install or remove

the blade.

Fig.9

To remove the blade, press the shaft lock so that the

blade cannot revolve and use the hex wrench to loosen

the hex bolt counterclockwise. Then remove the hex

bolt, outer flange and blade.

Fig.10

To install the blade, follow the removal procedure in

reverse. BE SURE TO TIGHTEN THE HEX BOLT

CLOCKWISE SECURELY.

When changing blade, make sure to also clean the

upper and lower blade guards of accumulated metal

chips as discussed in the Maintenance section. Such

efforts do not replace the need to check lower guard

operation before each use.

Hex wrench storage

Fig.11

When not in use, store the hex wrench as shown in the

figure to keep it from being lost.

Installing or removing hook

CAUTION:

• Never hang the tool on a waist belt or like.

Dangerous accidental cut may result.

• Never hook the tool at high location or on

potentially unstable surface.

Fig.12

The hook can be installed on the motor side of the tool

as illustrated. To install the hook, insert it into a groove

on the tool housing, and secure it with the screw. To

remove the hook, loosen the screw and take it off.

OPERATION

CAUTION:

• Always insert the battery cartridge all the way until

it locks in place. If you can see the red indicator on

the upper side of the button, it is not locked

completely. Insert it fully until the red indicator

cannot be seen. If not, it may accidentally fall out

of the tool, causing injury to you or someone

around you.

• Be sure to move the tool forward in a straight line

gently. Forcing or twisting the tool will result in

overheating the motor and dangerous kickback,

possibly causing severe injury.

• If the tool is operated continuously until the battery

cartridge has discharged, allow the tool to rest for

15 minutes before proceeding with a fresh battery.

• Never twist or force the tool in the cut. This may

cause motor overload and/or a dangerous

kickback, resulting in serious injury to the operator.

•

Always wear eye protection or goggle before operation.

Fig.13

Hold the tool firmly. The tool is provided with both a front grip

and rear handle. Use both to best grasp the tool. If both hands

are holding the tool, they cannot be cut by the blade. Set the

base on the workpiece to be cut without the blade making any

contact. Then turn the tool on and wait until the blade attains

full speed. Now simply move the tool forward over the

workpiece surface, keeping it flat and advancing smoothly until

the cutting is completed.

To get clean cuts, keep your cutting line straight and your

speed of advance uniform. If the cut fails to properly follow

your intended cut line, do not attempt to turn or force the tool

back to the cut line. Doing so may bind the blade and lead to

dangerous kickback and possible serious injury. Release

switch, wait for blade to stop and then withdraw tool. Realign

tool on new cut line, and start cut again. Attempt to avoid

positioning which exposes operator to chips and particles

being ejected from the tool. Use eye protection to help avoid

injury.

Fig.14

The sight grooves in the base makes it easy to check

the distance between the front edge of the blade and

the workpiece whenever the blade is set to the

maximum depth of cut.

CAUTION:

• Do not use a deformed or cracked blade. Replace

it with a new one.

• Do not stack materials when cutting them.

• Do not cut hardened steel, wood, plastics,

concrete, tile, etc. Cut only mild steel, aluminum

and stainless steel with a suitable saw blade.

• Do not touch the blade, workpiece or cutting chips

with your bare hand immediately after cutting, they

may be extremely hot and could burn your skin.

•

Always use the blades appropriate for your job.

The

use of inappropriate blades may cause a poor cutting

performance and/or present a risk of personal injury.

Rip fence (Guide rule) (optional accessory)

Fig.15

The handy rip fence allows you to do extra-accurate

straight cuts. Simply slide the rip fence up snugly

against the side of the workpiece and secure it in

position with the clamp screw on the front of the base. It

also makes repeated cuts of uniform width possible.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DCS551 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info