Bedienungsanleitung Makita DCS553 (Seite 9 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691884

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

9 ENGLISH

Indicating the remaining battery capacity

Only for battery cartridges with the indicator

►Fig.3: 1. Indicator lamps 2. Check button

Pressthecheckbuttononthebatterycartridgetoindi-

catetheremainingbatterycapacity.Theindicatorlamps

light up for a few seconds.

Indicator lamps Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

Thebattery

mayhave

malfunctioned.

NOTE: Depending on the conditions of use and the

ambienttemperature,theindicationmaydifferslightly

fromtheactualcapacity.

Switch action

WARNING: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

WARNING: NEVER defeat the lock-off button

by taping down or some other means. A switch with

anegatedlock-offbuttonmayresultinunintentional

operationandseriouspersonalinjury.

WARNING:

NEVER use the tool if it runs when you

simply pull the switch trigger without pressing the lock-off

button.Aswitchinneedofrepairmayresultinunintentional

operationandseriouspersonalinjury.ReturntooltoaMakita

service center for proper repairs BEFORE further usage.

Topreventtheswitchtriggerfrombeingaccidentallypulled,alock-

off button is provided. To start the tool, depress the lock-off button

and pull the switch trigger. Release the switch trigger to stop.

►Fig.4: 1. Switch trigger 2. Lock-off button

NOTICE: Do not pull the switch trigger hard

without pressing in the lock-off button. This can

cause switch breakage.

CAUTION: The tool starts to brake the cir-

cular saw blade rotation immediately after you

release the switch trigger. Hold the tool rmly to

respond the reaction of the brake when releasing

the switch trigger. Sudden reaction can drop the tool

offyourhandandcancauseapersonalinjury.

Automatic speed change function

This tool has "high speed mode" and "high torque mode".

Thetoolautomaticallychangestheoperationmode

depending on the work load. When the work load is low,

the tool will run in the "high speed mode" for quicker cut-

ting operation. When the work load is high, the tool will run

in the "high torque mode" for powerful cutting operation.

►Fig.5: 1. Mode indicator

The mode indicator lights up in green when the tool is

running in "high torque mode".

If the tool is operated with excessive load, the mode

indicator will blink in green. The mode indicator stops

blinkingandthenlightsuporturnsoffifyoureducethe

load on the tool.

Mode indicator status Operation

mode

On Off Blinking

High speed

mode

High torque

mode

Overload

alert

Adjusting depth of cut

CAUTION: After adjusting the depth of cut,

always tighten the lever securely.

Loosen the lever and move the base up or down. At the

desireddepthofcut,securethebasebytighteningthelever.

For cleaner, safer cuts, set cut depth so that no more

thanonebladetoothprojectsbelowworkpiece.Using

proper cut depth helps to reduce potential for danger-

ousKICKBACKSwhichcancausepersonalinjury.

►Fig.6: 1. Lever 2. Loosen 3. Tighten

Sighting

Placethealignmentlineofthebaseonyourintended

cutting line on the workpiece.

►Fig.7: 1. Alignment line 2. Cutting line 3. Base

Lighting the lamp

CAUTION: Do not look in the light or see the

source of light directly.

To turn on the lamp without running the tool, pull the

switch trigger without pressing the lock-off button.

To turn on the lamp with the tool running, press and hold

the lock-off button and pull the switch trigger.

The lamp goes out 10 seconds after releasing the

switch trigger.

►Fig.8: 1. Lamp

NOTE:Useadryclothtowipethedirtoffthelensof

the lamp. Be careful not to scratch the lens of lamp, or

itmaylowertheillumination.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DCS553 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info