Bedienungsanleitung Makita DCS553 (Seite 11 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691884

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

11 ENGLISH

OPERATION

CAUTION: Always wear eye protection or

goggle before operation.

CAUTION: Be sure to move the tool forward

in a straight line gently. Forcing or twisting the tool

will result in overheating the motor and dangerous

kickback,possiblycausingsevereinjury.

CAUTION: Never twist or force the tool in

the cut.Thismaycausemotoroverloadand/ora

dangerouskickback,resultinginseriousinjurytothe

operator.

CAUTION: Always use the circular saw blades

appropriate for your job. The use of inappropriate

circularsawbladesmaycauseapoorcuttingperfor-

manceand/orpresentariskofpersonalinjury.

CAUTION: Do not use a deformed or cracked

circular saw blade. Replace it with a new one.

►Fig.17

Holdthetoolrmly.Thetoolisprovidedwithbothafront

grip and rear handle. Use both to best grasp the tool. If

bothhandsareholdingthetool,theycannotbecutby

the circular saw blade. Set the base on the workpiece

tobecutwithoutthecircularsawblademakingany

contact. Then turn the tool on and wait until the circular

sawbladeattainsfullspeed.Nowsimplymovethetool

forwardovertheworkpiecesurface,keepingitatand

advancingsmoothlyuntilthecuttingiscompleted.

Togetcleancuts,keepyourcuttinglinestraightand

yourspeedofadvanceuniform.Ifthecutfailsto

properlyfollowyourintendedcutline,donotattempt

to turn or force the tool back to the cut line. Doing so

maybindthecircularsawbladeandleadtodangerous

kickbackandpossibleseriousinjury.Releaseswitch,

wait for the circular saw blade to stop and then withdraw

tool. Realign tool on new cut line, and start cut again.

Attempt to avoid positioning which exposes operator to

chipsandparticlesbeingejectedfromthetool.Useeye

protectiontohelpavoidinjury.

Thesightgroovesinthebasemakesiteasytocheck

the distance between the front edge of the circular saw

blade and the workpiece whenever the circular saw

blade is set to the maximum depth of cut.

►Fig.18: 1. Cutting line 2. Base 3. Sight grooves

CAUTION: Do not stack materials when cut-

ting them.

CAUTION: Do not cut hardened steel, wood,

plastics, concrete, tile, etc. Cut only mild steel,

aluminum and stainless steel with a suitable

circular saw blade.

CAUTION: Do not touch the circular saw

blade, workpiece or cutting chips with bare hands

immediately after cutting.Theymaybeextremely

hotandcouldburnyourskin.

CAUTION: If the tool is operated continuously

until the battery cartridge has discharged, allow

the tool to rest for 15 minutes before proceeding

with a fresh battery.

Rip fence (Guide rule)

Optional accessory

CAUTION:

Make sure that the rip fence is

securely installed in the correct position before use.

Improperattachmentmaycausedangerouskickback.

►Fig.19: 1. Rip fence (Guide rule) 2. Clamping screw

Thehandyripfenceallowsyoutodoextra-accurate

straightcuts.Simplyslidetheripfenceupsnugly

against the side of the workpiece and secure it in posi-

tion with the clamping screw on the front of the base. It

also makes repeated cuts of uniform width possible.

Lanyard (tether strap) connection

Safety warnings specic for use at height

Read all safety warnings and instructions. Failure

tofollowthewarningsandinstructionsmayresultin

seriousinjury.

Always keep the tool tethered when working "at

height". Maximum lanyard length is 2 m (6.5 ft).

2. Use only with lanyards appropriate for this tool

type and rated for at least 4.0 kg (8.8 lbs).

3. Do not anchor the tool lanyard to anything on

your body or on movable components. Anchor

the tool lanyard to a rigid structure that can

withstand the forces of a dropped tool.

4. Make sure the lanyard is properly secured at

each end prior to use.

5. Inspect the tool and lanyard before each use

for damage and proper function (including

fabric and stitching). Do not use if damaged or

not functioning properly.

6. Do not wrap lanyards around or allow them to

come in contact with sharp or rough edges.

7. Fasten the other end of the lanyard outside

the working area so that a falling tool is held

securely.

8. Attach the lanyard so that the tool will move

away from the operator if it falls. Dropped tools

willswingonthelanyard,whichcouldcauseinjury

or loss of balance.

9. Do not use near moving parts or running

machinery.Failuretodosomayresultinacrush

orentanglementhazard.

10. Do not carry the tool by the attachment device

or the lanyard.

11. Only transfer the tool between your hands

while you are properly balanced.

12. Do not attach lanyards to the tool in a way that

keeps guards, switches or lock-offs from oper-

ating properly.

13. Avoid getting tangled in the lanyard.

14.

Keep lanyard away from the cutting area of the tool.

15. Use multi-action and screw gate type cara-

bineers. Do not use single action spring clip

carabineers.

16. In the event the tool is dropped, it must be

tagged and removed from service, and should

be inspected by a Makita Factory or Authorized

Service Center.

►Fig.20: 1.Holeforlanyard(tetherstrap)

Makita DCS553 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info