Bedienungsanleitung Makita DFR540 (Seite 6 von 48) (Deutsch, Polnisch)

600456

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Tips for maintaining maximum battery life

1. Charge the battery cartridge before

completely discharged.

Always stop tool operation and charge the

battery cartridge when you notice less tool

power.

2. Never recharge a fully charged battery

cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room

temperature at 10 ﾟ C - 40 ﾟ C (50 ﾟ F - 104 ﾟ F).

Let a hot battery cartridge cool down before

charging it.

4. Charge the battery cartridge once in every six

months if you do not use it for a long period of

time.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before adjusting or

checking function on the tool.

Installing or removing battery cartridge

Fig.1

• Always switch off the tool before installing or

removing of the battery cartridge.

• To remove the battery cartridge, slide it from the

tool while sliding the button on the front of the

cartridge.

• To install the battery cartridge, align the tongue on

the battery cartridge with the groove in the housing

and slip it into place. Always insert it all the way

until it locks in place with a little click. If you can see

the red indicator on the upper side of the button, it is

not locked completely. Install it fully until the red

indicator cannot be seen. If not, it may accidentally

fall out of the tool, causing injury to you or someone

around you.

• Do not use force when installing the battery

cartridge. If the cartridge does not slide in easily, it

is not being inserted correctly.

Battery protection system

(Lithium-ion battery with star marking)

Fig.2

Lithium-ion batteries with a star marking are equipped

with a protection system. This system automatically cuts

off power to the tool to extend battery life.

The tool will automatically stop during operation if the tool

and/or battery are placed under one of the following

conditions:

• Overloaded:

The tool is operated in a manner that causes

it to draw an abnormally high current.

In this situation, release the trigger switch on

the tool and stop the application that caused

the tool to become overloaded. Then pull the

trigger switch again to restart.

If the tool does not start, the battery is

overheated. In this situation, let the battery

cool before pulling the trigger switch again.

• Low battery voltage:

The remaining battery capacity is too low and

the tool will not operate. In this situation,

remove and recharge the battery.

Setting for desired screw length

Fig.3

There are 7 positive-lock screw length settings. To obtain

the desired setting, pull out the stopper base while

depressing the lever until you see the number of the

desired screw length (indicated on the label on feeder

box) appear to rest in the fenestella of stopper base. See

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DFR540 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita DFR540

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info