Bedienungsanleitung Makita DFR540 (Seite 7 von 48) (Deutsch, Polnisch)

600456

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

the table below for the relation between the number

indicated on the label on feeder box and the respective

screw length.

For Models DFR540, DFR550

25 mm

30 mm

35 mm

40 mm

45 mm

50 mm

55 mm

Number indicated on the label Screw length

008238

For Model DFR750

Number indicated on the label Screw length

45 mm

50 mm

55 mm

60 mm

65 mm

70 mm

75 mm

008241

Adjusting the driving depth

Fig.4

Depress the stopper base as far as it will go. While

keeping it in this position, turn the adjusting knob until the

bit tip projects approx. 5 mm from the stopper base. Drive

a trial screw. If the screw head projects above the surface

of the workpiece, turn the adjusting knob in the "A"

direction; if the screw head is counter-sunk, turn the

adjusting knob in the "B" direction.

Switch action

Fig.5

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the "OFF" position when

released.

To start the tool, simply pull the switch trigger. Release

the switch trigger to stop.

Reversing switch action

Fig.6

This tool has a reversing switch to change the direction of

rotation. Depress the reversing switch lever from the A

side for clockwise rotation or from the B side for

counterclockwise rotation.

When the reversing switch lever is in the neutral position,

the switch trigger cannot be pulled.

CAUTION:

• Always check the direction of rotation before

operation.

• Use the reversing switch only after the tool comes

to a complete stop. Changing the direction of

rotation before the tool stops may damage the tool.

• When not operating the tool, always set the

reversing switch lever to the neutral position.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out

any work on the tool.

Installing or removing the bit

Loosen the thumb screws which secure the casing. Pull

out the casing in the direction of the arrow.

Fig.7

Press the dust cover toward the plane bearing and pull

out the bit. If the dust cover cannot be moved as far as

the plane bearing, try it again after turning the bit slightly.

To install the bit, insert it into the socket while turning it

slightly. After installing, always make sure that the bit is

securely held in place by trying to pull it out.

Fig.8

Installing screw strip

Insert the screw strip through the screw guide. Then

insert it through the feeder box until the first screw

reaches the position next to the driving position.

Fig.9

Fig.10

Removing screw strip

To remove the screw strip, just pull it out in the direction

of the arrow. If you depress the reverse button, you can

pull out the screw strip in the reverse direction of the

arrow.

Fig.11

Fig.12

Folding screw guide

Fig.13

Screw guide is foldable. Folding the screw guide allows

space used for storage to be minimal.

Carry hook

The carry hook is convenient for temporarily hooking the

tool. It can be installed on either side of the tool.

When removing the carry hook, widen it by pressing its

right ends ON BOTH SIDES in the directions of arrow (1)

and raise it in the direction of the arrow (2).

Fig.14

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DFR540 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita DFR540

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info