Bedienungsanleitung Makita DHP482RTJ (Seite 9 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

711039

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

9 ENGLISH

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing driver bit/

drill bit

Optional accessory

►Fig.10: 1. Sleeve 2. Close 3. Open

Turnthesleevecounterclockwisetoopenthechuck

jaws.Placethedriverbit/drillbitinthechuckasfar

asitwillgo.Turnthesleeveclockwisetotightenthe

chuck.Toremovethedriverbit/drillbit,turnthesleeve

counterclockwise.

Installing hook

►Fig.11: 1. Groove 2. Hook 3. Screw

Thehookisconvenientfortemporarilyhangingthetool.

Thiscanbeinstalledoneithersideofthetool.Toinstall

the hook, insert it into a groove in the tool housing on

eithersideandthensecureitwithascrew.Toremove,

loosen the screw and then take it out.

Installing driver bit holder

Optional accessory

►Fig.12: 1.Driverbitholder2.Driverbit

Fitthedriverbitholderintotheprotrusionatthetoolfoot

on either right or left side and secure it with a screw.

Whennotusingthedriverbit,keepitinthedriverbit

holders.Driverbits45mm-longcanbekeptthere.

OPERATION

CAUTION: Always insert the battery cartridge

all the way until it locks in place. If you can see the

redindicatorontheuppersideofthebutton,itisnot

locked completely. Insert it fully until the red indicator

cannotbeseen.Ifnot,itmayaccidentallyfalloutof

thetool,causinginjurytoyouorsomeonearound

you.

CAUTION: When the speed comes down

extremely, reduce the load or stop the tool to

avoid the tool damage.

Holdthetoolrmlywithonehandonthegripandthe

otherhandonthebottomofthebatterycartridgeto

control the twisting action.

►Fig.13

Screwdriving operation

CAUTION: Adjust the adjusting ring to the

proper torque level for your work.

CAUTION: Make sure that the driver bit is

inserted straight in the screw head, or the screw

and/or driver bit may be damaged.

First, turn the action mode changing ring so that the

arrowonthetoolbodypointstothe marking.

Placethepointofthedriverbitinthescrewheadand

apply pressure to the tool. Start the tool slowly and then

increase the speed gradually. Release the switch trigger

as soon as the clutch cuts in.

NOTE: When driving wood screw, pre-drill a pilot hole

2/3thediameterofthescrew.Itmakesdrivingeasier

and prevents splitting of the workpiece.

Hammer drilling operation

CAUTION: There is a tremendous and sud-

den twisting force exerted on the tool/drill bit

at the time of hole breakthrough, when the hole

becomes clogged with chips and particles, or

when striking reinforcing rods embedded in the

concrete.

First, turn the action mode changing ring so that the

arrowonthetoolbodypointstothe marking.The

adjustingringcanbealignedinanytorquelevelsfor

this operation.

Besuretouseatungsten-carbidetippeddrillbit.

Positionthedrillbitatthedesiredlocationforthehole,

then pull the switch trigger. Do not force the tool. Light

pressuregivesbestresults.Keepthetoolinposition

and prevent it from slipping away from the hole.

Donotapplymorepressurewhentheholebecomes

clogged with chips or particles. Instead, run the tool at

anidle,thenremovethedrillbitpartiallyfromthehole.

Byrepeatingthisseveraltimes,theholewillbecleaned

outandnormaldrillingmayberesumed.

Blow-out bulb

Optional accessory

►Fig.14: 1.Blow-outbulb

Afterdrillingthehole,usetheblow-outbulbtocleanthe

dust out of the hole.

Drilling operation

First,turntheadjustingringsothatthepointerpointsto

the marking.Thenproceedasfollows.

Drilling in wood

Whendrillinginwood,thebestresultsareobtained

withwooddrillsequippedwithaguidescrew.Theguide

screwmakesdrillingeasierbypullingthedrillbitinto

the workpiece.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DHP482RTJ Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info