Bedienungsanleitung Makita DHP482RTJ (Seite 10 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

711039

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

10 ENGLISH

Drilling in metal

Topreventthedrillbitfromslippingwhenstartinga

hole, make an indentation with a center-punch and

hammeratthepointtobedrilled.Placethepointofthe

drillbitintheindentationandstartdrilling.

Useacuttinglubricantwhendrillingmetals.Theexcep-

tionsareironandbrasswhichshouldbedrilleddry.

CAUTION: Pressing excessively on the tool

will not speed up the drilling. In fact, this excessive

pressure will only serve to damage the tip of your drill

bit,decreasethetoolperformanceandshortenthe

service life of the tool.

CAUTION: Hold the tool rmly and exert care

when the drill bit begins to break through the

workpiece.Thereisatremendousforceexertedon

thetool/drillbitatthetimeofholebreakthrough.

CAUTION: A stuck drill bit can be removed

simply by setting the reversing switch to reverse

rotation in order to back out. However, the tool

may back out abruptly if you do not hold it rmly.

CAUTION: Always secure small workpieces

in a vise or similar hold-down device.

CAUTION: If the tool is operated continuously

until the battery cartridge has discharged, allow

the tool to rest for 15 minutes before proceeding

with a fresh battery.

MAINTENANCE

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before attempting to perform inspection or

maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

Replacing carbon brushes

►Fig.15: 1. Limit mark

Checkthecarbonbrushesregularly.

Replace them when they wear down to the limit mark.

Keepthecarbonbrushescleanandfreetoslipinthe

holders.Bothcarbonbrushesshouldbereplacedatthe

sametime.Useonlyidenticalcarbonbrushes.

1. Use a screwdriver to remove two screws then

remove the rear cover.

►Fig.16: 1. Rear cover 2. Screw

2. Raise the arm part of the spring and then place

itintherecessedpartofthehousingwithaslottedbit

screwdriver of slender shaft or the like.

►Fig.17: 1. Recessed part 2. Spring 3.Arm

3. Useplierstoremovethecarbonbrushcapsof

thecarbonbrushes.Takeouttheworncarbonbrushes,

insertthenewonesandreplacethecarbonbrushcaps

in reverse.

►Fig.18: 1.Carbonbrushcap

4. Make sure to place the lead wire in opposite side

of the arm.

►Fig.19: 1. Lead wire 2.Carbonbrushcap

5. Makesurethatthecarbonbrushcapshavetinto

theholesinbrushholderssecurely.

►Fig.20: 1. Hole 2.Carbonbrushcap

6. Reinstall the rear cover and tighten two screws

securely.

7. Insertthebatterycartridgeintothetoolandbreak

inbrushesbyrunningtoolwithnoloadforabout1

minute.

8. Checkthetoolwhilerunningandelectricbrake

operation when releasing the switch trigger. If electric

brakeisnotworkingwell,askMakitaAuthorizedor

Factory Service Centers for repair.

TomaintainproductSAFETYandRELIABILITY,

repairs,anyothermaintenanceoradjustmentshould

beperformedbyMakitaAuthorizedorFactoryService

Centers, always using Makita replacement parts.

OPTIONAL

ACCESSORIES

CAUTION: These accessories or attachments

are recommended for use with your Makita tool

specied in this manual.Theuseofanyother

accessories or attachments might present a risk of

injurytopersons.Onlyuseaccessoryorattachment

for its stated purpose.

If you need any assistance for more details regard-

ing these accessories, ask your local Makita Service

Center.

• Drillbits

• Driverbits

• Tungsten-carbidetippeddrillbit

• Blow-outbulb

• Driverbitholder

• Hook

• Makitagenuinebatteryandcharger

NOTE:Someitemsinthelistmaybeincludedinthe

toolpackageasstandardaccessories.Theymay

differ from country to country.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DHP482RTJ Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info