Bedienungsanleitung Makita DHR182 (Seite 16 von 152) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691040

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

16 ENGLISH

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Side grip (auxiliary handle)

CAUTION: Always use the side grip to ensure

safe operation.

CAUTION:

After installing or adjusting the side

grip, make sure that the side grip is rmly secured.

Installthesidegripsothatthegroovesonthegriptin

theprotrusionsonthetoolbarrel.Turnthegripclock-

wisetosecureit.Thegripcanbexedatdesiredangle.

►Fig.11: 1. Side grip

Grease

Coat the shank end of the drill bit beforehand with a

small amount of grease (about 0.5 - 1 g).

Thischucklubricationassuressmoothactionandlon-

ger service life.

Installing or removing drill bit

Clean the shank end of the drill bit and apply grease

before installing the drill bit.

►Fig.12: 1. Shank end 2. Grease

Insertthedrillbitintothetool.Turnthedrillbitandpush

it in until it engages.

Afterinstallingthedrillbit,alwaysmakesurethatthe

drill bit is securely held in place by trying to pull it out.

►Fig.13: 1. Drill bit

Toremovethedrillbit,pullthechuckcoverdownallthe

way and pull the drill bit out.

►Fig.14: 1. Drill bit 2. Chuck cover

Chisel angle (when chipping,

scaling or demolishing)

Thechiselcanbesecuredatthedesiredangle.Tochangethe

chisel angle, rotate the action mode changing knob to the O

symbol.Turnthechiseltothedesiredangle.

►Fig.15: 1.Actionmodechangingknob

Rotate the action mode changing knob to the

sym-

bol.Thenmakesurethatthechiselissecurelyheldin

place by turning it slightly.

Depth gauge

Thedepthgaugeisconvenientfordrillingholesof

uniform depth. Loosen the side grip and insert the depth

gaugeintotheholeonthesidegrip.Adjustthedepth

gauge to the desired depth and tighten the side grip

rmly.

►Fig.16: 1. Hole 2. Depth gauge

NOTE: Make sure that the depth gauge does not

touch the main body of the tool when attaching it.

Installing or removing dust

collection system

Optional accessory

Toremovethedustcollectionsystem,pullthetoolwhile

pressingthelock-offbutton.Toinstallit,insertthetool

into the dust collection system all the way until it locks in

place with a little click.

►Fig.17: 1. Lock-off button

Dust cup

Optional accessory

Use the dust cup to prevent dust from falling over the tool and

on yourself when performing overhead drilling operations.

Attachthedustcuptothebitasshowninthegure.Thesize

of bits which the dust cup can be attached to is as follows.

Model Bit diameter

Dust cup 5 6 mm - 14.5 mm

Dust cup 9 12 mm - 16 mm

►Fig.18: 1. Dust cup

Dust cup set

Optional accessory

Installing the dust cup set

NOTICE: If you purchase the dust cup set as

optional accessory, the standard side grip cannot

be used with the dust cup set being installed on

the tool. When the dust cup set is installed on the

tool, remove the grip from the standard side grip, and

then attach it to the optional grip base set.

►Fig.19: 1. Bolt 2. Grip 3. Optional grip base set

NOTICE:

Do not use the dust cup set when drilling in

metal or similar. It may damage the dust cup set due to the

heat produced by small metal dust or similar. Do not install

or remove the dust cup set with the drill bit installed in the

tool. It may damage the dust cup set and cause dust leak.

Before installing the dust cup set, remove the bit from

the tool if installed.

Installthespacersothatthegroovesonthespacertin

the protrusions on the tool barrel while widening it. Be careful

for the spring not to come off from the slit of spacer.

►Fig.20: 1. Spacer 2. Spring

►Fig.21

2. Install the side grip (optional grip base set and

the grip removed from standard side grip) so that the

grooveonthegriptintheprotrusiononthespacer.

Turnthegripclockwisetosecureit.

►Fig.22: 1. Side grip

3. Install the dust cup set so that the claws of the

dustcuptinintheslitsonthespacer.

►Fig.23: 1. Dust cup 2. Claws

NOTE: If you connect a vacuum cleaner to the dust

cup set, remove the dust cap before connecting it.

►Fig.24: 1. Dust cap

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DHR182 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info