Bedienungsanleitung Makita DHS630ZJ (Seite 8 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

711052

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

2. Do not attempt to remove cut material when blade

is moving. Wait until blade stops before grasping

cut material. Blades coast after turn off.

3. Avoid cutting nails. Inspect for and remove all

nails from lumber before cutting.

4. Place the wider portion of the saw base on that

part of the workpiece which is solidly supported,

not on the section that will fall off when the cut is

made. If the workpiece is short or small, clamp it

down. DO NOT TRY TO HOLD SHORT PIECES BY

HAND! (Fig. 5)

5. Before setting the tool down after completing a

cut, be sure that the guard has closed and the

blade has come to a complete stop.

6. Never attempt to saw with the circular saw held

upside down in a vise. This is extremely

dangerous and can lead to serious accidents.

(Fig. 6)

7. Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation and

skin contact. Follow material supplier safety data.

8. Do not stop the blades by lateral pressure on the

saw blade.

9. Do not use any abrasive wheels.

10. Only use the saw blade with the diameter that is

marked on the tool or specified in the manual. Use

of an incorrectly sized blade may affect the proper

guarding of the blade or guard operation which could

result in serious personal injury.

11. Keep blade sharp and clean. Gum and wood pitch

hardened on blades slows saw and increases

potential for kickback. Keep blade clean by first

removing it from tool, then cleaning it with gum and

pitch remover, hot water or kerosene. Never use

gasoline.

12. Wear a dust mask and hearing protection when

use the tool.

13. Always use the saw blade intended for cutting the

material that you are going to cut.

14. Only use the saw blades that are marked with a

speed equal or higher than the speed marked on

the tool.

15. (For European countries only)

Always use the blade which conforms to EN847-1.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity with

product (gained from repeated use) replace strict

adherence to safety rules for t he subject product.

MISUSE or failure to follow the safety rules stated in

this instruction manual may cause serious personal

injury.

IMPORTANT SAFETY

INSTRUCTIONS FOR BATTERY

CARTRIDGE

ENC007-12

1. Before using battery cartridge, read all

instructions and cautionary markings on (1)

battery charger, (2) battery, and (3) product using

battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively shorter,

stop operating immediately. It may result in a risk

of overheating, possible burns and even an

explosion.

4. If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any

conductive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a

breakdown.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

7. Do not incinerate the battery cartridge even if it is

severely damaged or is completely worn out. The

battery cartridge can explode in a fire.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject to

the Dangerous Goods Legislation requirements.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on packaging

and labeling must be observed.

For preparation of the item being shipped, consulting

an expert for hazardous material is required. Please

also observe possibly more detailed national

regulations.

Tape or mask off open contacts and pack up the

battery in such a manner that it cannot move around in

the packaging.

11. Follow your local regulations relating to disposal

of battery.

12. Use the batteries only with the products specified

by Makita. Installing the batteries to non-compliant

products may result in a fire, excessive heat,

explosion, or leak of electrolyte.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causing fires, personal injury and damage. It will also void

the Makita warranty for the Makita tool and charger.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged.

Always stop tool operation and charge the battery

cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room

temperature at 10°C - 40°C (50°F - 104°F). Let a hot

battery cartridge cool down before charging it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DHS630ZJ Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info