Bedienungsanleitung Makita DHS630ZJ (Seite 9 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

711052

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

4. Charge the battery cartridge if you do not use it for

a long period (more than six months).

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before adjusting or

checking function on the tool.

Installing or removing battery cartridge

(Fig. 7)

• Always switch off the tool before installing or removing

of the battery cartridge.

• To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

• To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If you can see the red indicator

on the upper side of the button, it is not locked

completely. Install it fully until the red indicator cannot

be seen. If not, it may accidentally fall out of the tool,

causing injury to you or someone around you.

• Do not use force when installing the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Battery protection system (Lithium-ion

battery with star marking) (Fig. 8)

Lithium-ion batteries with a star marking are equipped

with a protection system. This system automatically cuts

off power to the tool to extend battery life.

The tool will automatically stop during operation if the tool

and/or battery are placed under one of the following

conditions:

• Overloaded:

The tool is operated in a manner that causes it to

draw an abnormally high current.

In this situation, release the trigger switch on the tool

and stop the application that caused the tool to

become overloaded. Then pull the trigger switch

again to restart.

If the tool does not start, the battery is overheated. In

this situation, let the battery cool before pulling the

trigger switch again.

• Low battery voltage:

The remaining battery capacity is too low and the tool

will not operate. In this situation, remove and

recharge the battery.

Indicating the remaining battery capacity

Only for battery cartridges with the indicator (Fig. 9)

Press the check button on the battery cartridge to indicate

the remaining battery capacity. The indicator lamps light

up for a few seconds.

NOTE:

• Depending on the conditions of use and the ambient

temperature, the indication may differ slightly from the

actual capacity.

Adjusting depth of cut (Fig. 10)

CAUTION:

• After adjusting the depth of cut, always tighten the lever

securely.

Loosen the lever on the side of the rear handle and move

the base up or down. At the desired depth of cut, secure

the base by tightening the lever.

For cleaner, safer cuts, set cut depth so that no more than

one blade tooth projects below workpiece. Using proper

cut depth helps to reduce potential for dangerous

kickback which can cause personal injury.

Bevel cutting (Fig. 11)

Loosen the wing screw on the front and rear base. Set for

the desired angle (0° - 45°) by tilting accordingly, then

tighten the wing screw securely.

Sighting (Fig. 12)

For straight cuts, align the 0° position on the front of the

base with your cutting line. For 45° bevel cuts, align the

45° position with it. The position of the top guide is

adjustable.

Switch action (Fig. 13)

CAUTION:

• Before installing the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released.

• Do not pull the switch trigger hard without pressing the

lock-off lever. This can cause switch breakage.

To prevent the switch trigger from being accidentally

pulled, a lock-off lever is provided. To start the tool, press

the lock-off lever and pull the switch trigger. Release the

switch trigger to stop.

Indicator lamps

Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery may

have

malfunctioned.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DHS630ZJ Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info