Bedienungsanleitung Makita DHS783 (Seite 17 von 156) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691830

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

17 ENGLISH

For tool with the inner ange for a

15.88 mm hole-diameter saw blade

(country specic)

Mounttheinnerangewithitsrecessedsidefacing

outward onto the mounting shaft and then place circu-

larsawblade(withtheringattachedifneeded),outer

angeandhexbolt.

For tool without the ring

►Fig.25: 1. Mounting shaft 2.Innerange3. Circular

saw blade 4.Outerange5. Hex bolt

For tool with the ring

►Fig.26: 1. Mounting shaft 2.Innerange3. Circular

saw blade 4.Outerange5. Hex bolt

6. Ring

WARNING: BE SURE TO TIGHTEN THE HEX

BOLT CLOCKWISE SECURELY. Also be careful

not to tighten the bolt forcibly. Slipping your hand

from the hex wrench can cause a personal injury.

WARNING: If the ring is needed to mount the

blade onto the spindle, always be sure that the

correct ring for the blade's arbor hole you intend

to use is installed between the inner and the outer

anges.Useoftheincorrectarborholeringmay

result in the improper mounting of the blade causing

blade movement and severe vibration resulting in

possible loss of control during operation and in seri-

ouspersonalinjury.

Blade guard cleaning

Whenchangingthecircularsawblade,makesureto

also clean the upper and lower blade guards of accu-

mulated sawdust as discussed in the Maintenance

section. Such efforts do not replace the need to check

lower guard operation before each use.

Connecting a vacuum cleaner

Whenyouwishtoperformcleancuttingoperation,

connectaMakitavacuumcleanertoyourtool.Connect

ahoseofthevacuumcleanertothedustnozzleas

showninthegure.

►Fig.27: 1.Dustnozzle2. Screw

►Fig.28: 1. Hose 2. Vacuum cleaner

OPERATION

Thistoolisintendedtocutwoodproducts.Withappro-

priate Makita genuine circular saw blades, following

materials can also be sawed:

• Aluminum products

RefertoourwebsiteorcontactyourlocalMakitadealer

for the correct circular saw blades to be used for the

material to be cut.

Checking blade guard function

Set the bevel angle to 0°, and then retract the lower

guardmanuallytotheendandreleaseit.Thelower

guardisproperlyfunctioningif;

—

itisretractedabovethebasewithoutanyhindranceand;

—

itautomaticallyreturnsandcontactswiththestopper.

►Fig.29: 1. Upper guard 2. Lower guard 3. Base

4. Stopper 5. Open 6. Close

Ifthelowerguardisnotfunctioningproperly,checkif

saw dust is accumulated inside of the upper and lower

guards.Ifthelowerguardisnotfunctioningproperly

evenafterremovingdust,haveyourtoolservicedata

Makita service center.

Cutting operation

CAUTION: Wear dust mask when performing

cutting operation.

CAUTION: Be sure to move the tool forward

in a straight line gently. Forcing or twisting the tool

will result in overheating the motor and dangerous

kickback,possiblycausingsevereinjury.

NOTE:Whenthebatterycartridgetemperatureis

low,thetoolmaynotworktoitsfullcapacity.Atthis

time,forexample,usethetoolforalight-dutycutfor

awhileuntilthebatterycartridgewarmsupashigh

as room temperature. Then, the tool can work to its

fullcapacity.

►Fig.30

Holdthetoolrmly.Thetoolisprovidedwithbothafrontgrip

and rear handle. Use both to best grasp the tool. If both hands

areholdingsaw,theycannotbecutbythecircularsawblade.

Set the base on the workpiece to be cut without the circular

sawblademakinganycontact.Thenturnthetoolonandwait

untilthecircularsawbladeattainsfullspeed.Nowsimply

move the tool forward over the workpiece surface, keeping it

atandadvancingsmoothlyuntilthesawingiscompleted.

Togetcleancuts,keepyoursawinglinestraightandyour

speedofadvanceuniform.Ifthecutfailstoproperlyfollow

yourintendedcutline,donotattempttoturnorforcethe

toolbacktothecutline.Doingsomaybindthecircular

saw blade and lead to dangerous kickback and possible

seriousinjury.Releaseswitch,waitforcircularsawblade

to stop and then withdraw tool. Realign tool on new cut

line, and start cut again. Attempt to avoid positioning which

exposesoperatortochipsandwooddustbeingejected

fromsaw.Useeyeprotectiontohelpavoidinjury.

Rip fence (Guide rule)

CAUTION: Make sure that the rip fence is

securely installed in the correct position before

use.Improperattachmentmaycausedangerous

kickback.

►Fig.31: 1.Ripfence(Guiderule)2. Clamping screw

Thehandyripfenceallowsyoutodoextra-accurate

straightcuts.Simplyslidetheripfenceupsnugly

against the side of the workpiece and secure it in posi-

tion with the clamping screw on the front of the base. It

also makes repeated cuts of uniform width possible.

Makita DHS783 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info