Bedienungsanleitung Makita DHS783 (Seite 18 von 156) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691830

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

18 ENGLISH

Guide rail

Optional accessory

Placethetoolontherearendofguiderail.Turntwoadjust-

ingscrewsonthetoolbasesothatthetoolslidessmoothly

without a clatter. Hold both the front grip and rear handle of

thetoolrmly.Turnonthetoolandcutthesplinter-guard

along the full length with a stroke. Now the edge of the

splinter-guard corresponds to the cutting edge.

►Fig.32: 1.Adjustingscrews

Whenbevelcuttingwiththeguiderail,usetheslide

lever to prevent the tool from falling over.

Move the slide lever on the tool base in the direction of arrow

so that it engages the undercut groove in the guide rail.

►Fig.33: 1. Slide lever

Lanyard (tether strap) connection

Safety warnings specic for use at height

Read all safety warnings and instructions. Failure

tofollowthewarningsandinstructionsmayresultin

seriousinjury.

Always keep the tool tethered when working "at

height". Maximum lanyard length is 2 m (6.5 ft).

2. Use only with lanyards appropriate for this tool

type and rated for at least 6.0 kg (13.3 lbs).

3. Do not anchor the tool lanyard to anything on

your body or on movable components. Anchor

the tool lanyard to a rigid structure that can

withstand the forces of a dropped tool.

4. Make sure the lanyard is properly secured at

each end prior to use.

5. Inspect the tool and lanyard before each use

for damage and proper function (including

fabric and stitching). Do not use if damaged or

not functioning properly.

6. Do not wrap lanyards around or allow them to

come in contact with sharp or rough edges.

Fasten the other end of the lanyard outside the

working area so that a falling tool is held securely.

Attach the lanyard so that the tool will move away

from the operator if it falls. Dropped tools will swing on

thelanyard,whichcouldcauseinjuryorlossofbalance.

9. Do not use near moving parts or running

machinery.Failuretodosomayresultinacrush

orentanglementhazard.

10. Do not carry the tool by the attachment device

or the lanyard.

11. Only transfer the tool between your hands

while you are properly balanced.

12. Do not attach lanyards to the tool in a way that

keeps guards, switches or lock-offs from oper-

ating properly.

13. Avoid getting tangled in the lanyard.

14.

Keep lanyard away from the cutting area of the tool.

15. Use multi-action and screw gate type cara-

bineers. Do not use single action spring clip

carabineers.

16.

In the event the tool is dropped, it must be tagged

and removed from service, and should be inspected

by a Makita Factory or Authorized Service Center.

►Fig.34: 1.Holeforlanyard(tetherstrap)

WIRELESS ACTIVATION

FUNCTION

For DHS783 only

What you can do with the wireless

activation function

The wireless activation function enables clean and com-

fortableoperation.Byconnectingasupportedvacuum

cleanertothetool,youcanrunthevacuumcleaner

automaticallyalongwiththeswitchoperationofthetool.

►Fig.35

To use the wireless activation function, prepare following items:

• Awirelessunit(optionalaccessory)

• A vacuum cleaner which supports the wireless

activation function

The overview of the wireless activation function setting is

as follows. Refer to each section for detail procedures.

1. Installing the wireless unit

2. Tool registration for the vacuum cleaner

3. Starting the wireless activation function

Installing the wireless unit

Optional accessory

CAUTION: Place the tool on a at and stable

surface when installing the wireless unit.

NOTICE:

Clean the dust and dirt on the tool before

installing the wireless unit.Dustordirtmaycause

malfunction if it comes into the slot of the wireless unit.

NOTICE:

To prevent the malfunction caused by static,

touch a static discharging material, such as a metal part

of the tool, before picking up the wireless unit.

NOTICE:

When installing the wireless unit, always

be sure that the wireless unit is inserted in the cor

rect direction and the lid is completely closed.

1. Openthelidonthetoolasshowninthegure.

►Fig.36: 1. Lid

2. Insert the wireless unit to the slot and then close

the lid.

Wheninsertingthewirelessunit,aligntheprojections

with the recessed portions on the slot.

►Fig.37: 1.Wirelessunit2.Projection3. Lid

4. Recessed portion

Whenremovingthewirelessunit,openthelidslowly.

The hooks on the back of the lid will lift the wireless unit

asyoupullupthelid.

►Fig.38: 1.Wirelessunit2. Hook 3. Lid

After removing the wireless unit, keep it in the supplied

case or a static-free container.

NOTICE: Always use the hooks on the back of

the lid when removing the wireless unit. If the

hooks do not catch the wireless unit, close the lid

completelyandopenitslowlyagain.

Makita DHS783 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info