Bedienungsanleitung Makita DLM461 (Seite 12 von 27) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

690895

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

12 ENGLISH

CAUTION: Hold the upper handle rmly so

that it does not drop off your hand. Otherwise, the

handle may fall and cause an injury.

3. Attach holder A and holder B to the handle.

Position the cords as shown in the gure.

► Fig.3: 1. Cord 2. Holder A 3. Holder B

NOTE: When attaching holder A, be sure to x the

cord with the holder as shown in the gure.

Removing the mulching attachment

For DLM460

1. Open the rear cover.

► Fig.4: 1. Rear cover

2. Remove the mulching attachment while holding

down the lever.

► Fig.5: 1. Lever 2. Mulching attachment

For DLM461

1. Open the rear cover.

► Fig.6: 1. Rear cover

2. Remove the mulching attachment while pulling the

lever.

► Fig.7: 1. Mulching attachment 2. Lever

Installing the grass basket

1. Open the rear cover.

► Fig.8: 1. Rear cover

2. Hook the grass basket on the rod of the mower

body as shown in the gure.

► Fig.9: 1. Rod 2. Guard 3. Grass basket

NOTICE: Make sure that the guard on the grass

basket is facing downward. Otherwise, the grass

basket may not catch all of cut-off grass.

Attaching the mulching attachment

For DLM460

1. Open the rear cover, and then remove the grass

basket.

► Fig.10: 1. Rear cover 2. Grass basket

2. Attach the mulching attachment while holding

down the lever, and then release the lever to lock the

mulching attachment.

► Fig.11: 1. Lever 2. Mulching attachment

For DLM461

1. Open the rear cover, and then remove the grass

basket.

► Fig.12: 1. Rear cover 2. Grass basket

2. Attach the mulching attachment while pulling the

lever, and then release the lever to lock the mulching

attachment.

► Fig.13: 1. Mulching attachment 2. Lever

FUNCTIONAL DESCRIPTION

Installing or removing battery cartridge

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION:

Hold the tool and the battery cartridge

rmly when installing or removing battery cartridge.

Failure to hold the tool and the battery cartridge rmly may

cause them to slip off your hands and result in damage to

the tool and battery cartridge and a personal injury.

CAUTION: Make sure that you lock the battery

cover before use. Otherwise, mud, dirt, or water may

cause damage to the product or the battery cartridge.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

it may accidentally fall out of the tool, causing injury to

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

NOTE:

The tool does not work with only one battery cartridge.

To install the battery cartridge;

Pull up the locking lever, and then open the battery cover.

► Fig.14: 1. Battery cover 2. Locking lever

2. Align the tongue on the battery cartridge with the

slot on the mower then slide the cartridge until it locks in

place with a little click.

► Fig.15: 1. Battery cartridge

3. Insert the lock key in the place shown in the gure

as far as it will go.

► Fig.16: 1. Lock key

4. Close the battery cover and push it until it is

latched with the locking lever.

To remove the battery cartridge from the mower;

1. Pull up the battery cover locking lever and open

the battery cover.

2. Pull out the battery cartridge from the mower while

sliding the button on the front of the cartridge.

3. Pull out the lock key.

4. Close the battery cover.

Tool / battery protection system

The tool is equipped with a tool/battery protection sys-

tem. This system automatically cuts off power to the

motor to extend tool and battery life. The tool will auto-

matically stop during operation if the tool or battery is

placed under one of the following conditions:

Overload protection

When the battery is operated in a manner that causes

it to draw an abnormally high current, the tool automati-

cally stops and the main power lamp blinks in green. In

this situation, turn the tool off and stop the application

that caused the tool to become overloaded. Then turn

the tool on to restart.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DLM461 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info