Bedienungsanleitung Makita DLM461 (Seite 14 von 27) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

690895

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

14 ENGLISH

This mower is equipped with the interlock switch and han-

dle switch. If you notice anything unusual with either of

these switches, stop operation immediately and have them

checked by your nearest Makita Authorized Service Center.

Install the battery cartridges. Insert the lock key into

the interlock switch and then close the battery cover.

2. Press the main power switch.

3. Press the switch button and hold it.

4. Grab the upper handle and pull the switch lever.

► Fig.19: 1. Switch button 2. Upper handle 3. Switch

lever

NOTE: If the lock key is not inserted, the power lamp

blinks in green when you pull the switch lever.

5. Release the switch button as soon as the motor

starts running. The mower will continue to run until you

release the switch lever.

6. Release the switch lever to stop the motor.

Adjusting the mowing height

WARNING:

Never put your hand or leg under

the mower body when adjusting the mowing height.

WARNING: Always make sure that the lever

ts in the groove properly before operation.

For DLM460

The mowing height can be adjusted in the range of

between 20 mm and 75 mm.

For DLM461

The mowing height can be adjusted in the range of

between 16 mm and 71 mm.

Remove the lock key, and then pull the mowing height

adjusting lever outward of the mower body and move it

to your desired mowing height.

► Fig.20: 1. Mowing height adjusting lever

Hold the front grip with one hand, and then move the

mowing height adjusting lever with the other hand.

► Fig.21: 1. Mowing height adjusting lever 2. Front

grip

NOTE: The mowing height gures should be used

just as a guideline. Depending on the conditions of

the lawn or the ground, the actual lawn height may

become slightly different from the set height.

NOTE: Try a test mowing of grass in a less conspicu-

ous place to get your desired height.

Adjusting the handle height

CAUTION: Before removing the bolts, hold

the upper handle rmly. Otherwise, the handle may

fall and cause an injury.

The handle height can be adjusted in three levels.

1. Loosen the thumb nuts of the lower handle, and

then remove the bolts, washer, and thumb nuts.

► Fig.22: 1. Thumb nut 2. Washer 3. Bolt

2. Adjust the handle height.

3. Insert the bolts from inside, then attach washers

from outside, and then tighten the thumb nuts.

Using mulching attachment

The mulching attachment allows you to return the cut

grass to the ground without gathering the cut grass in the

grass basket. When you operate the machine with the

mulching attachment, be sure to remove the grass basket.

Electronic function

The machine is equipped with the electronic functions

for easy operation.

• Constant speed control

Electronic speed control for obtaining constant

speed. Possible to get ne nish, because the rotat-

ing speed is kept constant even under load condition.

• Soft start

The soft-start function minimizes start-up shock,

and makes the machine start smoothly.

OPERATION

Mowing

WARNING: Before mowing, clear away sticks

and stones from mowing area. Furthermore, clear

away any weeds from mowing area in advance.

WARNING: Always wear the safety goggles or

safety glasses with side shields when operating

the mower.

CAUTION:

If the cut grass or foreign object

blocks up inside of the mower body, be sure to

remove the lock key and battery cartridge and wear

gloves before removing the grass or foreign object.

NOTICE: Use this machine for mowing lawn only.

Do not mow weeds with this machine.

► Fig.23

Firmly hold the handle with both hands when mowing.

The mowing speed guideline is approximately 1 meter

per 4 seconds.

► Fig.24

The center lines of the front wheels are guidelines to

mowing width. Using the center lines as guidelines,

mow in strips. Overlap by one half to one third the previ-

ous strip to mow the lawn evenly.

► Fig.25: 1. Mowing width 2. Overlapping area

3. Center line

Change the mowing direction each time to prevent the

grass grain pattern from forming in just one direction.

► Fig.26

Periodically check the grass basket for mowed grass.

Empty the grass before it becomes full. Before every

periodical check, be sure to stop the mower then

remove the lock key and the battery cartridge.

NOTE: Using the mower with the grass basket full

prevents smooth blade rotation and places an extra

load on the motor, which may cause breakdown.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DLM461 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info