Bedienungsanleitung Makita DLM461 (Seite 15 von 27) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

690895

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

15 ENGLISH

Mowing a long-grass lawn

Do not try to cut long grass all at once. Instead, mow

the lawn in steps. Leave a day or two between mowings

until the lawn becomes evenly short.

► Fig.27

NOTE: Mowing long grass to a short length all at

once may cause the grass to die. The cut grass may

also block up inside of the mower body.

Emptying the grass basket

WARNING: To reduce a risk of accident, reg-

ularly check the grass basket for any damage or

weakened strength. Replace the grass basket if

necessary.

1. Release the switch lever.

2. Remove the lock key.

3. Open the rear cover and take out the grass basket

by holding the handle.

► Fig.28: 1. Rear cover 2. Handle 3. Grass basket

4. Empty the grass basket.

MAINTENANCE

WARNING: Always be sure that the lock

key and battery cartridge are removed from the

mower before storing or carrying the mower or

attempting to perform inspection or maintenance.

WARNING: Always remove the lock key when

the mower is not in use. Store the lock key in a

safe place out of reach of children.

WARNING: Wear gloves when performing

inspection or maintenance.

WARNING: Always wear the safety goggles or

safety glasses with side shields when performing

inspection or maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

To maintain product SAFETY and RELIABILITY,

repairs, any other maintenance or adjustment should

be performed by Makita Authorized or Factory Service

Centers, always using Makita replacement parts.

Maintenance

1. Remove the lock key and battery cartridges, and

then close the battery cover.

2. Put the mower on its side and clean grass clip-

pings accumulated on the underside of mower deck.

3. Pour water toward the bottom of the machine to

which the blade is attached.

NOTICE: Do not wash the machine with high

pressure water.

4. Check all nuts, bolts, knobs, screws, fasteners etc.

for tightness.

Inspect moving parts for damage, breakage, and wear.

Damaged or missing parts should be repaired or replaced.

6. Store the mower in a safe place out of the reach of

children.

Carrying the mower

When carrying the mower, hold the front grip and lower

handle with two people as shown in the gure.

► Fig.29: 1. Lower handle 2. Front grip

Storing

Store mower indoors in a cool, dry and locked place.

Don't store the mower and charger in locations where

the temperature may reach or exceed 40 °C (104 °F).

1. Open the rear cover and take out the grass basket

by holding the handle.

► Fig.30: 1. Rear cover 2. Handle 3. Grass basket

2. Loosen the thumb nuts and fold the upper handle.

► Fig.31: 1. Upper handle 2. Thumb nut

Removing or installing the mower blade

WARNING: Always remove the lock key and

battery cartridge when removing or installing the

blade. Failure to remove the lock key and battery

cartridge may cause a serious injury.

WARNING:

The blade coasts for a few seconds

after releasing the switch. Do not start any opera-

tion until the blade comes to a complete stop.

WARNING: Always wear gloves when han-

dling the blade.

Removing the mower blade

For DLM460

1. Put the mower on its side so that the mowing

height adjusting lever comes to the upper side.

2. To lock the blade, insert a lumber or similar into

the mower.

3. Turn the bolt counterclockwise with the wrench.

► Fig.32: 1. Mower blade 2. Wrench 3. Lumber

4. Remove the bolt, washer, mower blade in order.

► Fig.33: 1. Mower blade 2. Washer 3. Bolt

For DLM461

1. Put the mower on its side so that the mowing

height adjusting lever comes to the upper side.

2. Turn the bolt counterclockwise with the wrench

while holding the base plate.

► Fig.34: 1. Wrench 2. Base plate

3. Remove the bolt, washer, base plate in order.

► Fig.35: 1. Base plate 2. Washer 3. Bolt

To remove the individual blade, turn the bolt counter-

clockwise with the wrench while holding the base plate.

► Fig.36: 1. Base plate 2. Mower blade 3. Wrench

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DLM461 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info