Bedienungsanleitung Makita DLS111 (Seite 24 von 244) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691782

Zoom out

Zoom in

Vorherige Seite

1/244

Nächste Seite

24 ENGLISH

Thismitersawemployspositivestopfunction.Youcan

set0°,15°,22.5°,31.6°,45°,and60°right/leftmiter

anglequickly.Tousethisfunction,movetheturnbase

close to your desired positive stop angle while holding

downthelocklever.Thenreleasethelockleverand

move the turn base forward until the turn base is locked.

Adjusting the bevel angle

NOTICE: Always remove the upper guide fences

and vertical vise before adjusting the bevel angle.

NOTICE: When changing bevel angles, be sure

to position the kerf boards appropriately as

explained in the "Kerf boards" section.

NOTICE: When tilting the saw blade, be sure to

raise the handle fully.

NOTICE: Do not tighten the knob too hard. Doing

so may cause malfunction of the locking mecha-

nism of the bevel angle.

1. Turntheknobontheslidepolecounterclockwise.

►Fig.21: 1. Knob

2. Pull and turn the latch lever to the position as

illustrated.

►Fig.22: 1. Latch lever

3. Match the pointer with your desired angle on the

scale by moving the carriage then tighten the knob.

►Fig.23: 1. Bevel angle scale 2. Pointer

Totiltthecarriagetotheright,tiltthecarriagetotheleft

slightly and then tilt it to the right while pressing down

the releasing button.

►Fig.24: 1. Releasing button

If you perform a bevel cut greater than 45°, move the

carriage while sliding the releasing lever toward the

frontofthetool.Youcanperformupto48°bevelcut.

►Fig.25: 1. Releasing lever

Thismitersawemployspositivestopfunction.Youcan

set22.5°and33.9°angletobothrightandleftquickly.

Set the latch lever in the position as illustrated and tilt

thecarriage.Tochangetheangle,pullthelatchlever

and tilt the carriage.

►Fig.26: 1. Latch lever

CAUTION: After changing the bevel angle,

always secure the knob.

Slide lock

Tolocktheslidingmovementofthecarriage,pushthe

carriage toward the guide fence until it stops. Pull the

stopper pin and rotate it 90°.

►Fig.27: 1. Unlocked position 2. Locked position

3. Stopper pin

Switch action

WARNING: Before installing the batteries

into the tool, always check to see that the switch

trigger actuates properly and returns to the "OFF"

position when released. Do not pull the switch

trigger hard without pressing in the lock-off but-

ton. This can cause switch breakage. Operating a

tool with a switch that does not actuate properly can

leadtolossofcontrolandseriouspersonalinjury.

WARNING: NEVER use tool without a fully

operative switch trigger.Anytoolwithaninoper-

ativeswitchisHIGHLYDANGEROUSandmustbe

repaired before further usage or serious personal

injurymayoccur.

WARNING: NEVER defeat the lock-off button

by taping down or some other means.Aswitchwith

a negated lock-off button may result in unintentional

operationandseriouspersonalinjury.

WARNING: NEVER use the tool if it runs when

you simply pull the switch trigger without press-

ing the lock-off button.Aswitchinneedofrepair

may result in unintentional operation and serious

personalinjury.ReturntooltoaMakitaservicecenter

for proper repairs BEFORE further usage.

►Fig.28: 1. Switch trigger 2. Lock-off button 3. Hole

for padlock

Topreventtheswitchtriggerfrombeingaccidentally

pulled,alock-offbuttonisprovided.Tostartthetool,

press in the lock-off button and pull the switch trigger.

Release the switch trigger to stop.

Aholeisprovidedintheswitchtriggerforinsertionofa

padlock to lock the tool off.

WARNING: Do not use a lock with a shank or

cable any smaller than 6.35 mm (1/4") in diameter.

Asmallershankorcablemaynotproperlylockthe

tool in the off position and unintentional operation

mayoccurresultinginseriouspersonalinjury.

Electronic function

Constant speed control

Thetoolisprovidedwithanelectronicspeedcontrol

which helps maintain a constant blade rotation speed

evenunderload.Aconstantbladerotationspeedwill

result in a very smooth cut.

Soft start feature

Thisfunctionallowsthesmoothstart-upofthetoolby

limitingthestart-uptorque.

Laser beam action

For DLS111, DLS112 only

CAUTION: Never look into the laser beam.

Directlaserbeammayinjureyoureyes.

Toturnonthelaserbeam,presstheupperposition(I)

oftheswitch.Toturnoffthelaserbeam,pressthelower

position (0) of the switch.

►Fig.29: 1. Switch for laser

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DLS111 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info