Bedienungsanleitung Makita DLS111 (Seite 26 von 244) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691782

Zoom out

Zoom in

Vorherige Seite

1/244

Nächste Seite

26 ENGLISH

Securing workpiece

WARNING: It is extremely important to always

secure the workpiece correctly with the proper

type of vise or crown molding stoppers. Failure to

dosomayresultinseriouspersonalinjuryandcause

damagetothetooland/ortheworkpiece.

WARNING: After a cutting operation do not

raise the blade until it has come to a complete

stop.Theraisingofacoastingblademayresultin

seriouspersonalinjuryanddamagetotheworkpiece.

WARNING: When cutting a workpiece that

is longer than the support base of the saw, the

material should be supported the entire length

beyond the support base and at the same height

to keep the material level. Proper workpiece support

will help avoid blade pinch and possible kickback

whichmayresultinseriouspersonalinjury.Donot

relysolelyontheverticalviseand/orhorizontalvise

tosecuretheworkpiece.Thinmaterialtendstosag.

Support workpiece over its entire length to avoid

bladepinchandpossibleKICKBACK.

►Fig.41: 1. Support 2.Turnbase

Guide fences

WARNING: Before operating the tool, make

sure that the upper fence is secured rmly.

WARNING: Before bevel-cutting, make sure

that no part of the tool, especially the blade, con-

tacts the upper and lower fences when fully low-

ering and raising the handle in any position and

while moving the carriage through its full range

of travel. If the tool or blade makes contact with

the fence this may result in kickback or unexpected

movementofthematerialandseriouspersonalinjury.

Use upper fences to support the material higher than

the lower fences. Insert the upper fence into the hole on

the lower fence and tighten the clamping screw.

►Fig.42: 1. Upper fence 2. Lower fence 3. Clamping

screw 4.Adjustingscrew

NOTICE:Thelowerfencesarexedtothebasein

the factory. Do not remove the lower fences.

NOTICE: If the upper fence is still loose after tight-

eningtheclampingscrew,turntheadjustingscrewto

closeagap.Theadjustingscrewisfactoryadjusted.

Youdon'tneedtouseitunlessneeded.

Youcanstoretheupperfencesontotheholderwhen

not in use. Use the clip on the upper fence to hold it on

the holder.

►Fig.43: 1. Holder 2. Upper fence 3. Clip

Vertical vise

WARNING: The workpiece must be secured

rmly against the turn base and guide fence with

the vise during all operations. If the workpiece is

not properly secured against the fence the material

may move during the cutting operation causing

possible damage to the blade, causing the material

to be thrown and loss of control resulting in serious

personalinjury.

►Fig.44: 1. Vise arm 2. Vise rod 3. Clamping screw

4. Vise knob

Theverticalvisecanbeinstalledintwopositionson

either the left or right side of the base. Insert the vise

rod into the hole in the base.

Position the vise arm according to the thickness and

shape of the workpiece and secure the vise arm by

tightening the screw. If the clamping screw contacts

the carriage, install it on the opposite side of vise arm.

Make sure that no part of the tool contacts the vise

when lowering the handle all the way. If some part

contacts the vise, re-position the vise.

Presstheworkpieceatagainsttheguidefenceandthe

turn base. Position the workpiece at the desired cutting

positionandsecureitrmlybytighteningtheviseknob.

NOTE:Foraquicksettingofworkpiece,turningthe

vise knob to 90° counterclockwise allows the vise

knobtobemovedupanddown.Tosecurethework-

piece after setting, turn the vise knob clockwise.

Horizontal vise

Optional accessory

WARNING: Always rotate the vise nut clock-

wise until the workpiece is properly secured. If

the workpiece is not properly secured the material

may move during the cutting operation causing

possible damage to the blade, causing the material

to be thrown and loss of control resulting in serious

personalinjury.

WARNING: When cutting a thin workpiece,

such as base boards, against the fence, always

use the horizontal vise.

Thehorizontalvisecanbeinstalledintwopositionson

either the left or right side of the base. When performing

22.5° or greater miter cuts, install the horizontal vise on

the side opposite the direction in which the turn base is

to be turned.

►Fig.45: 1. Vise plate 2. Vise nut 3. Vise knob

Byippingthevisenutcounterclockwise,theviseis

released,andrapidlymovesinandout.Togripthe

workpiece, push the vise knob forward until the vise

platecontactstheworkpieceandipthevisenutclock-

wise.Thenturntheviseknobclockwisetosecurethe

workpiece.

NOTE:Themaximumwidthofworkpiecewhichcan

be secured by the horizontal vise is 228 mm.

Makita DLS111 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info