Bedienungsanleitung Makita DLS111 (Seite 34 von 244) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691782

Zoom out

Zoom in

Vorherige Seite

1/244

Nächste Seite

34 ENGLISH

State of abnormality Probable cause (malfunction) Remedy

Thevacuumcleanerdoesnotrun

along with the switch operation of

the tool.

Thewirelessunitisnotinstalledinto

the tool.

Thewirelessunitisimproperlyinstalled

into the tool.

Install the wireless unit correctly.

Theterminalofthewirelessunitand/or

the slot is dirty.

Gently wipe off dust and dirt on the terminal of the

wireless unit and clean the slot.

Thewirelessactivationbuttononthe

tool has not been pushed.

Pushthewirelessactivationbuttonbrieyandmake

sure that the wireless activation lamp is blinking

in blue.

Thestand-byswitchonthevacuum

cleanerisnotsetto"AUTO".

Set the stand-by switch on the vacuum cleaner to

"AUTO".

More than 10 tools are registered to the

vacuum cleaner.

Perform the tool registration again.

If more than 10 tools are registered to the vacuum

cleaner, the tool registered earliest will be cancelled

automatically.

Thevacuumcleanererasedalltool

registrations.

Perform the tool registration again.

No power supply Supply the power to the tool and the vacuum

cleaner.

Thetoolandvacuumcleanerisaway

from each other (out of the transmission

range).

Get the tool and vacuum cleaner closer each other.

Themaximumtransmissiondistanceisapproxi-

mately 10 m however it may vary according to the

circumstances.

Radio disturbance by other appliances

which generate high-intensity radio

waves.

Keep the tool and vacuum cleaner away from the

appliances such as Wi-Fi devices and microwave

ovens.

Thevacuumcleanerrunswhilethe

tool's switch trigger is not pulled.

Other users are using the wireless

activation of the vacuum cleaner with

their tools.

Turnoffthewirelessactivationbuttonoftheother

tools or cancel the tool registration of the other

tools.

MAINTENANCE

WARNING: Always be sure that the tool is

switched off and batteries are removed before

attempting to perform inspection or maintenance.

Failure to removing the batteries and switch off the

tool may result in accidental start up of the tool which

mayresultinseriouspersonalinjury.

WARNING: Always be sure that the blade is

sharp and clean for the best and safest perfor-

mance.Attemptingacutwithadulland/ordirtyblade

may cause kickback and result in a serious personal

injury.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

Adjusting the cutting angle

Thistooliscarefullyadjustedandalignedatthefactory,

but rough handling may have affected the alignment. If

your tool is not aligned properly, perform the following:

Miter angle

Lower the handle fully and lock it in the lowered position

by the stopper pin. Push the carriage toward the guide

fence. Loosen the grip and the screws which secure the

pointer and miter angle scale.

►Fig.70: 1. Screw on pointer 2. Screws on miter

angle scale 3. Miter scale

Set the turn base to the 0° position using the positive

stopfunction.Squarethesideofthebladewiththeface

oftheguidefenceusingatriangularruleortry-square.

Whilekeepingthesquare,tightenthescrewsonthe

miteranglescale.Afterthat,alignthepointers(both

right and left) with the 0° position in the miter angle

scale and then tighten the screw on the pointer.

►Fig.71: 1.Triangularrule

Bevel angle

0° bevel angle

Push the carriage toward the guide fence and lock the

sliding movement by the stopper pin. Lower the handle

fully and lock it in the lowered position by the stopper

pinandthenloosentheknob.Turnthe0°adjusting

bolt two or three revolutions counterclockwise to tilt the

blade to the right.

►Fig.72: 1.0°Adjustingbolt2. Screw

Carefullysquarethesideofthebladewiththetop

surface of the turn base using the triangular rule, try-

square,etc.byturningthe0°adjustingboltclockwise.

Thentightentheknobrmlytosecurethe0°angleyou

have set.

►Fig.73: 1.Triangularrule2. Saw blade 3.Topsur-

face of turn base

Checkifthesideofthebladesquareswiththeturnbase

surface once again. Loosen the screw on the pointer.

Alignthepointerwith0°positioninthebevelangle

scale and then tighten the screw.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DLS111 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info