Bedienungsanleitung Makita DLS111 (Seite 35 von 244) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691782

Zoom out

Zoom in

Vorherige Seite

1/244

Nächste Seite

35 ENGLISH

45° bevel angle

NOTICE: Before adjusting the 45° bevel angle,

nish 0° bevel angle adjustment.

Loosen the knob and fully tilt the carriage to the side

that you want to check. Check if the pointer indicates

the 45° position in the bevel angle scale.

►Fig.74

If the pointer does not indicate the 45° position, align

itwith45°positionbyturningtheadjustingboltonthe

opposite side of the bevel angle scale.

►Fig.75: 1.Left45°adjustingbolt2.Right45°adjust-

ing bolt

Adjusting the laser line position

For DLS111, DLS112 only

WARNING:

The batteries must be installed

while adjusting the laser line. Take extra care not

to switch on the tool during adjustment.Accidental

startupofthetoolmayresultinseriouspersonalinjury.

CAUTION: Never look directly into the laser

beam. Direct eye exposure to the beam could cause

serious damage to your eyes.

NOTICE: Check the position of laser line regu-

larly for accuracy.

NOTICE: Beware that impacts to the tool. It may

cause the laser line to be misaligned or may cause

damage to the laser, shortening its life.

NOTICE: Have the tool repaired by a Makita

authorized service center for any failure on the

laser unit.

Themovablerangeoflaserlineisdecidedbytherange

adjustmentscrewsonbothsides.Performfollowing

procedures to alter the laser line position.

1. Remove the batteries.

2. Draw a cutting line on the workpiece and place it

ontheturnbase.Atthistime,donotsecurethework-

piece with a vise or similar securing device.

3. Lower the handle and align the cutting line with

the saw blade.

Return the handle to the original position and secure

the workpiece with the vertical vise so that the workpiece

does not move from the position you have determined.

5. Install the batteries and turn on the laser switch.

6. Loosentheadjustingscrew.Tomovethelaserline

awayfromtheblade,turntherangeadjustmentscrews

counterclockwise.Tomovethelaserlineclosetothe

blade,turntherangeadjustmentscrewclockwise.

Adjusting the laser line on the left side of the blade

►Fig.76:

1.Adjustingscrew2.Rangeadjustmentscrew

3. Hex wrench 4. Laser line 5. Saw blade

Adjusting the laser line on the right side of the blade

►Fig.77:

1.Adjustingscrew2.Rangeadjustmentscrew

3. Hex wrench 4. Laser line 5. Saw blade

7. Slidetheadjustingscrewtothepositionthatthe

laser line comes onto the cutting line and then tighten.

NOTE:

Themovablerangeoflaserlineisfactoryadjusted

within1mm(0.04")fromthesidesurfaceofblade.

Cleaning the laser light lens

For DLS111, DLS112 only

Thelaserlightbecomeshardtoseeasthelensforthelaser

light gets dirty. Clean the lens for laser light periodically.

►Fig.78: 1. Screw 2. Lens

Remove the batteries. Loosen the screw and pull out

the lens. Clean the lens gently with a damp soft cloth.

NOTICE: Do not remove the screw which

secures the lens. If the lens does not come out,

loosen the screw further.

NOTICE: Do not use solvents or any petro-

leum-based cleaners on the lens.

After use

Afteruse,wipeoffchipsanddustadheringtothetool

with a cloth or the like. Keep the blade guard clean

according to the directions in the previously covered

sectiontitled"Bladeguard".Lubricatetheslidingpor-

tions with machine oil to prevent rust.

TomaintainproductSAFETYandRELIABILITY,

repairs,anyothermaintenanceoradjustmentshould

beperformedbyMakitaAuthorizedorFactoryService

Centers, always using Makita replacement parts.

OPTIONAL

ACCESSORIES

WARNING: These Makita accessories or

attachments are recommended for use with your

Makita tool specied in this manual.Theuseof

any other accessories or attachments may result in

seriouspersonalinjury.

WARNING: Only use the Makita accessory

or attachment for its stated purpose. Misuse of

an accessory or attachment may result in serious

personalinjury.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Steel&Carbide-tippedsawblades

• Verticalvise

• Horizontalvise

• Crownmoldingstopperset

• Dustbag

• Triangularrule

• Hexwrench

• Hexwrench(forlaseradjustment)

• Wirelessunit(forDLS111)

• Makitagenuinebatteryandcharger

NOTE: Some items in the list may be included in the

toolpackageasstandardaccessories.Theymay

differ from country to country.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DLS111 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info