Bedienungsanleitung Makita DLS600 (Seite 17 von 160) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691786

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

17 ENGLISH

Indicating the remaining battery

capacity

Only for battery cartridges with the indicator

►Fig.7: 1. Indicator lamps 2. Check button

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

Indicator lamps Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may differ slightly

from the actual capacity.

Automatic speed change function

►Fig.8: 1. Mode indicator

Mode indicator status Operation mode

High speed mode

High torque mode

This tool has "high speed mode" and "high torque

mode". It automatically changes operation mode

depending on the work load. When mode indicator

lights up during operation, the tool is in high torque

mode.

Stopper pin

CAUTION: Always hold the handle when

releasing the stopper pin. Otherwise the handle

springsupanditmayresultinpersonalinjury.

To release the stopper pin, keep applying a slight

downward pressure on the handle and then pulling the

stopper pin.

►Fig.9: 1. Stopper pin

Blade guard

WARNING: Never defeat or remove the blade

guard or the spring which attaches to the guard.

An exposed blade as a result of defeated guarding

mayresultinseriouspersonalinjuryduringoperation.

WARNING: Never use the tool if the blade

guard or spring are damaged, faulty or removed.

Operation of the tool with a damaged, faulty or

removedguardmayresultinseriouspersonalinjury.

CAUTION: Always maintain the blade guard

in good condition for safe operation. Stop the

operation immediately if there are any irregularity

of the blade guard. Check to assure spring loaded

return action of guard.

►Fig.10: 1. Blade guard

When lowering the handle, the blade guard raises

automatically. The guard is spring loaded so it returns to

its original position when the cut is completed and the

handle is raised.

Cleaning

►Fig.11: 1. Blade guard

If the transparent blade guard becomes dirty, or saw-

dust adheres to it in such a way that the blade and/or

workpiece is no longer easily visible, remove the battery

cartridge and clean the guard carefully with a damp

cloth. Do not use solvents or any petroleum-based

cleaners on the plastic guard because this may cause

damage to the guard.

For cleaning, raise the blade guard by referring to

"Installing or removing saw blade".

After cleaning, make sure to return the blade and center

cover and tighten the hex socket bolt.

1. Make sure that the tool is switched off and the

battery cartridges are removed.

2. Turn the hex socket bolt counterclockwise using

the supplied hex wrench with holding the center cover.

3. Raise the blade guard and center cover.

4. When cleaning is complete, return the center

cover and tighten the hex socket bolt by performing the

steps above in reverse.

WARNING: Do not remove spring holding

blade guard. If guard becomes damaged in course

of time or UV light exposure, contact a Makita ser-

vice center for replacement. DO NOT DEFEAT OR

REMOVE GUARD.

Positioning kerf board

This tool is provided with the kerf boards in the turn

base to minimize tearing on the exit side of a cut. The

kerfboardsarefactoryadjustedsothatthesawblade

doesnotcontactthekerfboards.Beforeuse,adjustthe

kerf boards as follows:

1. Make sure to remove the battery cartridge. Then,

loosen all the screws (2 each on left and right) securing

the kerf boards.

►Fig.12: 1. Kerf board 2. Screw

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DLS600 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info