Bedienungsanleitung Makita DLS600 (Seite 18 von 160) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691786

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

18 ENGLISH

2. Re-tighten them only to the extent that the kerf

boards can still be easily moved by hand.

3. Lower the handle fully and push in the stopper pin

to lock the handle in the lowered position.

4. Adjustthekerfboardssothatthekerfboardsjust

contact the sides of the blade teeth.

►Fig.13

►Fig.14: 1. Saw blade 2. Blade teeth 3. Kerf board

4. Left bevel cut 5. Straight cut

5. Tightenthescrews(donottightenrmly).

Afteradjustingthekerfboards,releasethestopperpin

and raise the handle. Then tighten all the screws securely.

NOTICE: After setting the bevel angle ensure

that the kerf boards are adjusted properly. Correct

adjustmentofthekerfboardshelpstoprovideproper

support of the workpiece and minimizing workpiece

tear out.

Maintaining maximum cutting

capacity

Thistoolisfactoryadjustedtoprovidethemaximum

cutting capacity for a 165 mm saw blade.

When installing a new blade, always check the lower limit

positionoftheblade,andifnecessary,adjustitasfollows:

1. Remove the battery cartridge. Lower the handle

completely.

2. Usethehexwrenchtoturnthelowerlimitadjust-

ing bolt until the saw blade comes slightly below the

cross section of the guide fence and the top surface of

the turn base.

►Fig.15: 1.Adjustingbolt

►Fig.16: 1. Guide fence

3. Rotate the blade by hand while holding the handle

all the way down to be sure that the blade does not

contactanypartofthelowerbase.Re-adjustslightly,if

necessary.

WARNING: After installing a new blade and

with the battery cartridge removed, always be

sure that the blade does not contact any part of

the lower base when the handle is lowered com-

pletely. If a blade makes contact with the base it may

causekickbackandresultinseriouspersonalinjury.

►Fig.17

Sub-fence

Country specic

This tool is equipped with the sub-fence and small

sub-fences.

Sub-fence

WARNING: Always remove sub-fence when

performing bevel cuts. Failure to do so may cause

seriousinjury.

►Fig.18: 1. Sub-fence

When performing cuts except for bevel cuts, use the

sub-fence to support the workpiece.

Small sub-fence

CAUTION: When performing right bevel cuts,

fold the small sub-fences. Otherwise, they may

contact the blade or a part of the tool, and may result

inseriousinjurytotheoperator.

►Fig.19: 1. Small sub-fence 2. Scale

Whenperformingverticalcutorleftbevelcut,ipthem

upward to support the workpiece. The guide fence has

a scale of 10 mm interval.

Adjusting the miter angle

►Fig.20: 1. Fixing screw 2. Turn base 3. Miter scale

4. Pointer

1. Loosenthexingscrewcounterclockwise.

2. Adjusttheangleoftheturnbase.Usethepointer

and the miter scale as a guide.

3. Tightenthexingscrewclockwisermly.

CAUTION: After changing the miter angle,

always secure the turn base by tightening the

xing screw rmly.

NOTICE: When turning the turn base, be sure to

raise the handle fully.

Adjusting the bevel angle

Toadjustthebevelangle,turntheleverattherearof

the tool downward.

►Fig.21: 1. Lever

To tilt the blade to the left, hold the handle and tilt the saw

head. Use the bevel scale and the pointer as a guide.

Thenturntheleverupwardrmlytosecurethesawhead.

►Fig.22: 1. Pointer 2. Bevel scale

To tilt the blade to the right, hold the handle and tilt the

saw head to the left slightly, and push the release button.

With the release button pressed, tilt the saw blade to the

right.Turntheleverupwardrmlytosecurethesawhead.

►Fig.23: 1. Release button

CAUTION: After changing the bevel angle,

always secure the saw head by turning the lever

upward rmly.

NOTICE: When tilting the saw blade, be sure the

handle is fully raised.

NOTICE: When changing bevel angles, be

sure to position the kerf boards appropriately

as explained in the "Positioning kerf boards"

section.

Setting 46° bevel angle

1. Loosen the lever and tilt the blade to the left or

right fully.

►Fig.24: 1. Lever

2. To tilt the blade to the left, hold the handle and tilt

the saw head to the right slightly, and then move the

release lever to the direction of the arrow. The bevel

anglecanbeadjustedbetween45°to46°bytiltingthe

saw head while moving the release lever.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DLS600 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info