Bedienungsanleitung Makita DLS600 (Seite 20 von 160) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691786

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

20 ENGLISH

Aligning the laser line

Align the cutting line on your workpiece with the laser

line.

►Fig.31

A) When you want to obtain the correct size on the left side

of workpiece, shift the laser line to the left of the blade.

B) When you want to obtain the correct size on the right

side of workpiece, shift the laser line to the right of the

blade.

ASSEMBLY

WARNING: Always be sure that the tool is

switched off and the battery cartridge is removed

before working on the tool. Failure to switch off and

remove the battery cartridge may result in serious

personalinjury.

Hex wrench storage

Thehexwrenchisstoredasshowninthegure.When

the hex wrench is needed it can be pulled out of the

wrench holder.

After using the hex wrench it can be stored by returning

it to the wrench holder.

►Fig.32: 1. Wrench holder 2. Hex wrench

Installing or removing saw blade

WARNING: Always be sure that the tool is

switched off and the battery cartridge is removed

before installing or removing the blade. Accidental

start up of the tool may result in serious personal

injury.

CAUTION: Use only the Makita hex wrench

provided to install or remove the blade. Failure

todosomayresultinovertighteningorinsufcient

tightening of the hex socket bolt. This could cause

aninjury.

To remove the blade, perform the following steps:

1. Release the stopper pin, and then lock the handle

in the raised position by pushing in the stopper pin.

►Fig.33: 1. Stopper pin

2. Use the hex wrench to loosen the hex socket bolt

holding the center cover by turning it counterclockwise.

Then, raise the blade guard and center cover.

►Fig.34: 1. Center cover 2. Hex socket bolt 3. Hex

wrench 4. Blade guard

3. Press the shaft lock to lock the spindle and use

the hex wrench to loosen the hex socket bolt clockwise.

Then remove the hex socket bolt of the spindle, outer

angeandblade.

►Fig.35: 1. Shaft lock 2. Hex socket bolt 3. Outer

ange

4. Iftheinnerangeisremoved,installitonthespin-

dle with its blade mounting part facing the blade. If the

angeisinstalledincorrectlytheangewillrubagainst

the machine.

►Fig.36: 1.Outerange2. Saw blade 3.Innerange

4. Hex socket bolt (left-handed) 5. Spindle

6. Blade mounting part

To install the blade, perform the following steps:

1. Mountthebladecarefullyontotheinnerange.

Make sure that the direction of the arrow on the blade

matches the direction of the arrow on the blade case.

►Fig.37: 1. Saw blade 2. Arrow

2. Installtheouterangeandhexsocketbolt,and

then use the hex wrench to tighten the hex socket bolt

(left-handed) of the spindle securely counterclockwise

while pressing the shaft lock.

3. Return the blade guard and center cover to its

original position. Then tighten the hex socket bolt of the

center cover clockwise to secure the center cover.

4. Release the handle from the raised position by

pulling the stopper pin. Lower the handle to make sure

that the blade guard moves properly.

5. Make sure the shaft lock has released spindle

before making cut.

For tool with the inner ange for

15.88 mm hole-diameter saw blade

Country specic

Mounttheinnerangewithitsrecessedsidefacing

outward onto the mounting shaft and then place saw

blade(withtheringattachedifneeded),outerange

and hex bolt.

For tool without the ring

►Fig.38: 1.Outerange2. Saw blade 3.Innerange

4. Hex socket bolt (left-handed) 5. Spindle

For tool with the ring

►Fig.39: 1.Outerange2. Saw blade 3.Innerange

4. Hex socket bolt (left-handed) 5. Ring

6. Spindle

WARNING: If the ring is needed to mount the

blade onto the spindle, always be sure that the

correct ring for the blade's arbor hole you intend

to use is installed between the inner and the outer

anges. Use of the incorrect arbor hole ring may

result in the improper mounting of the blade causing

blade movement and severe vibration resulting in

possible loss of control during operation and in seri-

ouspersonalinjury.

For tool with the inner ange for

other than 20 mm or 15.88 mm hole-

diameter saw blade

Country specic

Theinnerangehasacertaindiameterofablade

mounting part on one side of it and a different diameter

of blade mounting part on the other side. Choose a

correctsideonwhichblademountingparttsintothe

saw blade hole perfectly.

►Fig.40: 1.Outerange2. Saw blade 3.Innerange

4. Hex socket bolt (left-handed) 5. Spindle

6. Blade mounting part

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DLS600 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info