Bedienungsanleitung Makita DLS600 (Seite 21 von 160) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691786

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

21 ENGLISH

CAUTION:

Make sure that the blade mounting part

"a" on the inner ange that is positioned outside ts

into the saw blade hole "a" perfectly. Mounting the blade

on the wrong side can result in the dangerous vibration.

Dust bag

The use of the dust bag makes cutting operations

cleaner and dust collection easier.

Toattachthedustbag,titontothedustnozzle.

When the dust bag is about half full, remove the dust bag

from the tool and pull the fastener out. Empty the dust bag of

its contents, tapping it lightly so as to remove particles adher-

ing to the insides which might hamper further collection.

►Fig.41: 1. Dust bag 2. Dust nozzle 3. Fastener

NOTE: If you connect a vacuum cleaner to your saw,

cleaner operations can be performed.

►Fig.42

Securing workpiece

WARNING: It is extremely important to always

secure the workpiece correctly with the vise.

Failuretodosomayresultinseriouspersonalinjury

and cause damage to the tool and/or the workpiece.

WARNING:

When cutting a workpiece that is

longer than the support base of the saw, the mate-

rial should be supported the entire length beyond

the support base and at the same height to keep the

material level. Proper workpiece support will help avoid

blade pinch and possible kickback which may result in

seriouspersonalinjury.Donotrelysolelyonthevertical

vise and/or horizontal vise to secure the workpiece. Thin

material tends to sag. Support workpiece over its entire

length to avoid blade pinch and possible KICKBACK.

►Fig.43: 1. Support 2. Turn base

Vertical vise

WARNING: Secure the workpiece rmly

against the turn base and guide fence with the

vise during all operations. Otherwise the material

may move during the cutting operation, cause dam-

age to the blade, and be thrown which may result in

lossofcontrolandseriouspersonalinjury.

Install the vertical vise on either the left or right side of the

guide fence. Insert the vise rod into the hole in the guide

fence and tighten the lower screw to secure the vise rod.

►Fig.44: 1. Vise arm 2. Vise knob 3. Guide fence

4. Turn base 5. Lower screw 6. Upper screw

7. Vise rod

Position the vise arm according to the thickness and

shape of the workpiece and secure the vise arm by

tightening the upper screw. If the upper screw contacts

the guide fence, install the upper screw on the opposite

side of vise arm. Make sure that no part of the tool con-

tacts the vise when lowering the handle fully. If some

part contacts the vise, re-position the vise.

Presstheworkpieceatagainsttheguidefenceandthe

turn base. Position the workpiece at the desired cutting

positionandsecureitrmlybytighteningtheviseknob.

Attaching the shoulder strap

Optional accessory

CAUTION: Be sure to remove the shoulder

strap before operating the tool. The shoulder

strap may be entangled and cause injury.

CAUTION: Be sure to attach the hooks of the

shoulder strap to the tool securely. If the hooks

are attached incompletely, they may come off and

cause injury.

The shoulder strap is convenient for transporting the

tool. Attach the hooks of the shoulder strap to the tool

asshowninthegure.

►Fig.45: 1. Shoulder strap 2. Hook

OPERATION

WARNING: Make sure the blade is not con-

tacting the workpiece, etc. before the switch

is turned on. Turning the tool on with the blade in

contact with the workpiece may result in kickback and

seriouspersonalinjury.

WARNING: After a cutting operation, do not

raise the blade until it has come to a complete

stop. The raising of a coasting blade may result in

seriouspersonalinjuryanddamagetotheworkpiece.

NOTICE: Before use, be sure to release the

handle from the lowered position by pulling the

stopper pin.

NOTICE: Do not apply excessive pressure on the

handle when cutting. Too much force may result in

overloadofthemotorand/ordecreasedcuttingef-

ciency. Press down handle with only as much force as

necessaryforsmoothcuttingandwithoutsignicant

decrease in blade speed.

NOTICE: Gently press down the handle to per-

form the cut. If the handle is pressed down with force

or if lateral force is applied, the blade may vibrate and

leave a mark (saw mark) in the workpiece and the

precision of the cut may be impaired.

Press cutting (cutting small

workpieces)

►Fig.46

Workpieces up to 46 mm high and 92 mm wide can be

cut in the following manner.

1. Secure the workpiece with the vise.

2. Switch on the tool without the blade making any

contact and wait until the blade attains full speed before

lowering.

3. Gently lower the handle to the fully lowered posi-

tion to cut the workpiece.

4. When the cut is completed, switch off the tool and

wait until the blade has come to a complete stop

before returning the blade to its fully elevated position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DLS600 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info