Bedienungsanleitung Makita DLS600 (Seite 23 von 160) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691786

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

23 ENGLISH

MAINTENANCE

WARNING: Always be sure that the blade is

sharp and clean for the best and safest perfor-

mance. Attempting a cut with a dull and /or dirty blade

may cause kickback and result in a serious personal

injury.

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before attempting to perform inspection or

maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

To maintain product SAFETY and RELIABILITY,

repairs,anyothermaintenanceoradjustmentshould

be performed by Makita Authorized or Factory Service

Centers, always using Makita replacement parts.

Adjusting the cutting angle

Thistooliscarefullyadjustedandalignedatthefactory,

but rough handling may have affected the alignment. If

your tool is not aligned properly, perform the following:

Miter angle

1. Loosenthexingscrewcounterclockwise.

2. Rotate the turn base until the pointer indicates 0°

on the miter scale.

►Fig.52: 1. Fixing screw 2. Turn base 3. Miter scale

4. Pointer

3. Rotate the turn base slightly clockwise and coun-

terclockwise to seat the turn base in the 0° miter notch.

(Leave as it is if the pointer does not indicate 0°.)

4. Loosen the hex socket bolt securing the guide

fence using the hex wrench.

►Fig.53: 1. Guide fence 2. Hex socket bolt

►Fig.54: 1. Guide fence 2. Hex socket bolt

5. Lower the handle fully and lock it in the lowered

position by pushing in the stopper pin.

6. Adjusttheguidefenceuntilitmakesaperpendic-

ular angle with the blade using a triangular rule, try-

square, etc. Then securely tighten the hex socket bolt

on the guide fence.

►Fig.55: 1. Guide fence 2. Triangular rule 3. Saw

blade

7. Make sure that the pointer indicates 0° on the

miter scale. If the pointer does not indicate 0°, loosen

thescrewwhichsecuresthepointerandadjustthe

pointer so that it indicates 0°.

►Fig.56: 1. Screw 2. Miter scale 3. Pointer

Bevel angle

0° bevel angle

1. Lower the handle fully and lock it in the lowered

position by pushing in the stopper pin.

2. Loosen the lever at the rear of the tool.

3. Turnthe0°bevelangleadjustingboltontheright

side of the saw head two or three revolutions counter-

clockwise to tilt the blade to the right.

►Fig.57: 1.Adjustingbolt2. Lever

4. Turnthe0°bevelangleadjustingboltclockwise

carefully until the side of the blade makes a perpendic-

ular angle with the top surface of the turn base. Use the

triangular rule, try-square, etc. as a guide. Then tighten

the lever securely.

►Fig.58: 1. Triangular rule 2. Saw blade 3. Top sur-

face of turn table

5. Make sure that the pointer on the arm indicates 0°

on the bevel scale. If it does not indicate 0°, loosen the

screwwhichsecuresthepointerandadjustthepointer

so that it indicates 0°.

►Fig.59: 1. Screw 2. Pointer 3. Bevel scale

45° bevel angle

Adjustthe45°bevelangleonlyafterperforming0°

bevelangleadjustment.

1. Loosen the lever and tilt the blade to the left fully.

2. Make sure that the pointer on the arm indicates

45° on the bevel scale. If the pointer does not indicate

45°,turntheleft45°bevelangleadjustingboltonthe

right side of the arm until the pointer indicates 45°.

►Fig.60: 1.Right45°bevelangleadjustingbolt

2. Pointer 3.Left45°bevelangleadjusting

bolt

3. Tiltthebladetotherightfully,andthenadjustthe

right 45° bevel angle using the right 45° bevel angle

adjustingbolt.

►Fig.61: 1. Saw blade 2. Triangular rule

Adjusting the laser line position

WARNING: The battery cartridge must be

installed on the tool while adjusting the laser line.

Take extra care not to switch on the tool during

adjustment. Accidental start up of the tool may result

inseriouspersonalinjury.

CAUTION: Never look directly into the laser

beam. Direct eye exposure to the beam could cause

serious damage to your eyes.

NOTICE: Check the position of laser line regu-

larly for accuracy.

NOTICE: Beware that impacts to the tool. It may

cause the laser line to be misaligned or may cause

damage to the laser, shortening its life.

NOTICE: Have the tool repaired by a Makita

authorized service center for any failure on the

laser unit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DLS600 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info