Bedienungsanleitung Makita DLS600 (Seite 24 von 160) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691786

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

24 ENGLISH

The movable range of laser line is decided by the range

adjustmentscrewsonbothsides.Performfollowing

procedures to alter the laser line position.

1. Remove the battery cartridge.

2. Draw a cutting line on the workpiece and place it

on the turn base. At this time, do not secure the work-

piece with a vise or similar securing device.

3. Lower the handle and align the cutting line with

the saw blade.

►Fig.62: 1. Cutting line

4. Return the handle to the original position and

secure the workpiece with the vertical vise so that the

workpiece does not move from the position you have

determined.

►Fig.63: 1. Vise

5. Install the battery cartridge to the tool and turn on

the laser switch.

6. Loosentheadjustingscrew.Tomovethelaserline

awayfromtheblade,turntherangeadjustmentscrews

counterclockwise. To move the laser line close to the

blade,turntherangeadjustmentscrewclockwise.

Adjusting the laser line on the left side of the blade

►Fig.64: 1.Adjustingscrew2.Rangeadjustment

screw 3. Hex wrench 4. Laser line 5. Saw

blade

Adjusting the laser line on the right side of the

blade

►Fig.65: 1.Rangeadjustmentscrew2. Hex wrench

3. Laser line 4. Saw blade

7. Slidetheadjustingscrewtothepositionthatthe

laser line comes onto the cutting line and then tighten.

NOTE: The movable range of laser line is factory

adjustedwithin1mmfromthesidesurfaceofblade.

Cleaning the laser light lens

The laser light becomes hard to see as the lens for

the laser light gets dirty. Clean the lens for laser light

periodically.

Remove the battery cartridge. Loosen the screw and

pull out the lens. Clean the lens gently with a damp soft

cloth.

►Fig.66: 1. Screw

►Fig.67: 1. Lens

NOTICE: Do not remove the screw which

secures the lens. If the lens does not come out,

loosen the screw further.

NOTICE: Do not use solvents or any petro-

leum-based cleaners on the lens.

After use

After use, wipe off chips and dust adhering to the tool

with a cloth or the like. Keep the blade guard clean

according to the directions in the previously covered

section titled "Blade guard". Lubricate the sliding por-

tions with machine oil to prevent rust.

OPTIONAL

ACCESSORIES

WARNING: These Makita accessories or

attachments are recommended for use with your

Makita tool specied in this manual. The use of

any other accessories or attachments may result in

seriouspersonalinjury.

WARNING: Only use the Makita accessory

or attachment for its stated purpose. Misuse of

an accessory or attachment may result in serious

personalinjury.

If you need any assistance for more details regard-

ing these accessories, ask your local Makita Service

Center.

• Carbide-tipped saw blades

• Holder rod assembly

• Set plate

• Shoulder strap

• Makita genuine battery and charger

NOTE: Some items in the list may be included in the

tool package as standard accessories. They may

differ from country to country.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DLS600 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info