Bedienungsanleitung Makita DRS780 (Seite 13 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691831

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

13 ENGLISH

For tool with the inner ange for a

15.88 mm hole-diameter saw blade

(country specic)

Mounttheinnerangewithitsrecessedsidefacing

outward onto the mounting shaft and then place circu-

larsawblade(withtheringattachedifneeded),outer

angeandhexbolt.

For tool without the ring

►Fig.21: 1. Mounting shaft 2.Innerange3. Circular

saw blade 4.Outerange5. Hex bolt

For tool with the ring

►Fig.22: 1. Mounting shaft 2.Innerange3. Circular

saw blade 4.Outerange5. Hex bolt

6. Ring

WARNING: BE SURE TO TIGHTEN THE HEX

BOLT COUNTERCLOCKWISE SECURELY. Also

be careful not to tighten the bolt forcibly. Slipping

your hand from the hex wrench can cause a per-

sonal injury.

WARNING: If the ring is needed to mount the

blade onto the spindle, always be sure that the

correct ring for the blade's arbor hole you intend

to use is installed between the inner and the outer

anges.Useoftheincorrectarborholeringmay

result in the improper mounting of the blade causing

blade movement and severe vibration resulting in

possible loss of control during operation and in seri-

ouspersonalinjury.

Blade guard cleaning

When changing the circular saw blade, make sure to

also clean the upper and lower blade guards of accu-

mulated sawdust as discussed in the Maintenance

section. Such efforts do not replace the need to check

lower guard operation before each use.

Connecting a vacuum cleaner

NOTE: In some countries, the tool does not have the

dustnozzle.

Whenyouwishtoperformcleancuttingoperation,

connectaMakitavacuumcleanertoyourtool.

►Fig.23: 1. Rubber cap

►Fig.24: 1. Rubber cap 2. Vacuum cleaner 3. Hose

Removetherubbercapfromthedustnozzleandcon-

nect the vacuum cleaner's hose as illustrated.

NOTE: To prevent the rubber cap from being lost,

store it on the front of the tool.

NOTE: When not using the vacuum cleaner, attach

therubbercapontothedustnozzle.

OPERATION

CAUTION: Be sure to move the tool forward

in a straight line gently. Forcing or twisting the tool

will result in overheating the motor and dangerous

kickback,possiblycausingsevereinjury.

NOTE:Whenthebatterycartridgetemperatureis

low,thetoolmaynotworktoitsfullcapacity.Atthis

time,forexample,usethetoolforalight-dutycutfor

awhileuntilthebatterycartridgewarmsupashigh

as room temperature. Then, the tool can work to its

fullcapacity.

►Fig.25

Holdthetoolrmly.Thetoolisprovidedwithbothafront

grip and rear handle. Use both to best grasp the tool.

Ifbothhandsareholdingsaw,theycannotbecutby

the circular saw blade. Set the base on the workpiece

tobecutwithoutthecircularsawblademakingany

contact. Then turn the tool on and wait until the circular

sawbladeattainsfullspeed.Nowsimplymovethetool

forwardovertheworkpiecesurface,keepingitatand

advancingsmoothlyuntilthesawingiscompleted.

Togetcleancuts,keepyoursawinglinestraightand

yourspeedofadvanceuniform.Ifthecutfailstoprop-

erlyfollowyourintendedcutline,donotattempttoturn

orforcethetoolbacktothecutline.Doingsomaybind

the circular saw blade and lead to dangerous kickback

andpossibleseriousinjury.Releaseswitch,waitforcir-

cular saw blade to stop and then withdraw tool. Realign

tool on new cut line, and start cut again. Attempt to

avoid positioning which exposes operator to chips and

wooddustbeingejectedfromsaw.Useeyeprotection

tohelpavoidinjury.

Hook

CAUTION: Always remove the batteries when

hanging the tool with the hook.

CAUTION: Never hook the tool at high loca-

tions or on the surfaces where the tool may lose

the balance and fall.

CAUTION: Do not pull the tool hooked

downward.

Thehookisconvenientforhangingthetooltemporarily.

Tousethehook,simplyliftuphookuntilitsnapsinto

the open position.

Whennotinuse,alwayslowerhookuntilitsnapsinto

the closed position.

►Fig.26: 1. Hook

►Fig.27

Rip fence (Guide rule)

Optional accessory

Thehandyripfenceallowsyoutodoextra-accurate

straightcuts.Simplyslidetheripfenceupsnugly

against the side of the workpiece and secure it in posi-

tion with the clamping screw on the front of the base. It

also makes repeated cuts of uniform width possible.

►Fig.28: 1.Ripfence(Guiderule)2. Clamping screw

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DRS780 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info