Bedienungsanleitung Makita DSC102 (Seite 10 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691563

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

10 ENGLISH

Overheat protection

When the tool is overheated, the tool automatically

stops and the LED light will blink. Let the tool cool down

before turning the tool on again.

Overdischarge protection

When the battery capacity becomes low, the tool stops

automatically. If the product does not operate even

when the switches are operated, remove the batteries

from the tool and charge the batteries.

Indicating the remaining battery

capacity

Only for battery cartridges with the indicator

► Fig.3: 1. Indicator lamps 2. Check button

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

Indicator lamps Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may differ slightly

from the actual capacity.

Switch action

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

To start the cutting operation, continue to pull the switch

trigger. The cutting die on the movable mount will

overlap with the die on the stationary mount and then

returns. If you release the switch trigger before complet-

ing the cut, the cutting dice will stop.

► Fig.4: 1. Switch trigger

► Fig.5: 1. Stationary mount 2. Cutting die 3. Movable

mount

NOTICE: Do not operate the tool at no-load

unnecessarily.

Auto-stop function

When you continue to pull the switch trigger, the jaw of

the dice once closes and returns to fully opened posi-

tion then stops. Release the trigger and pull it again to

begin the next cutting sequence.

Reversing switch lever

WARNING: When not operating the tool,

always set the reversing switch lever to the lock

position.

CAUTION: Always make sure the position of

the reversing switch lever before operating.

NOTICE: Do not move the reversing switch lever

when the switch trigger is being pulled. This may

cause a damage to the tool.

To start the cutting operation, set the reversing switch

lever to cutting position.

To reverse the cutting sequence, set the reversing

switch lever to the reversing position. When you con-

tinue to pull the switch trigger, the jaw of the cutting dice

opens and stops at fully opened position.

To lock the switch trigger, set the reversing switch lever

to the lock position. The switch trigger cannot be pulled

in this position.

► Fig.6: 1. Reversing switch lever 2. Cutting position

3. Lock position 4. Reversing position

NOTICE: When the reversing switch lever is

in the reversing position, run the tool only as

needed. To prevent the damage to the tool, the tool

will automatically stops when it is run in the reversing

position continuously.

NOTE: After cutting, if you release the switch trigger

while the jaw of the cutting dice is opening and then

set the reversing switch lever to the reversing posi-

tion, the jaw will once close and then open when you

pull the switch trigger again.

LED light

CAUTION: Do not look in the light or see the

source of light directly.

Pull the switch trigger to light up the lamp. The lamp

keeps on lighting while the switch trigger is being pulled.

The lamp goes out approximately 15 seconds after

releasing the switch trigger.

► Fig.7: 1. Lamp (inside)

NOTE: Use a dry cloth to wipe the dirt off the lens of

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

NOTE: When the tool is overheated, the lamp will

blink. Let the tool cool down in this case.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DSC102 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info