Bedienungsanleitung Makita DSC102 (Seite 12 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691563

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

12 ENGLISH

OPERATION

CAUTION: Make sure that the correct size of

the cutting dice are installed to the tool. Check

the cutting capacity written on the the cutting dice

before cutting.

CAUTION: Before pulling the switch trigger,

be sure to set the threaded rod so that its thread

ts with those of cutting dice. Incorrect alignment

of the threads may break the cutting dice and cause

personal injury by own off fractions.

CAUTION: Replace the cutting dice if the

cutting edge is chipped or deformed.

When cutting, place the threaded rod perpendicular to

the cutting line as shown in the gure.

► Fig.18: 1. Cutting line

NOTE: When cutting a threaded rod made of ductile

metal such as stainless steel, burrs may be generated

on the cut end. Remove burrs with a le in this case.

► Fig.19: 1. Threaded rod 2. Burr

Cutting secured threaded rods

When cutting a threaded rod which is secured to the

building structure such as the ceiling, wall, oor, etc.,

follow the procedure below :

► Fig.20: 1. Threaded rod 2. Cutting die on the sta-

tionary mount

1. Bring the tool so that the threaded rod is posi-

tioned between the cutting dice.

2. While the threaded rod contacting with the rod

guide, t the thread of the rod with that of the cutting die

on the stationary mount.

3. Pull and hold the switch trigger until the cutting is

nished and the jaw of the cutting dice comes to fully

opened position.

NOTICE: Clean the front face of the tool and the

tip of the guide scale before operation. They may

dirty the contacting surface.

Cutting loose threaded rods

When cutting a loose threaded rod on the oor or a

work table, follow the procedure below :

► Fig.21: 1. Threaded rod 2. Cutting die on the sta-

tionary mount

1. Position a threaded rod between the cutting dice.

2. While the threaded rod contacting with the rod

guide, t the thread of the rod with that of the cutting die

on the stationary mount.

3. Pull and hold the switch trigger until the cutting is

nished and the jaw of the cutting dice comes to fully

opened position.

When cutting a long threaded rod which is hard to hold

by hand, place the tool as illustrated. The tool can be

placed at. The cover also can be used for supporting

the end of the threaded rod.

► Fig.22: 1. Cover (Position 1) 2. Rod guide (Position

1) 3. Cover (Position 2) 4. Rod guide

(Position 2)

The cover has markings to indicate its position.

Depending on the size of the threaded rod, put the

cover in the position as shown in the table as well as the

rod guide.

Position Size of threaded rod

1 W3/8, M10

2 M8, M6

Quitting the cutting in the middle

CAUTION: Never try to pull out the tool forci-

bly from the threaded rod. It may cause unexpected

start up which cause personal injury or damage to the

cutting dice and tool.

When quitting the cutting in the middle, set the revers-

ing switch lever to the reversing position and pull the

switch trigger until the threaded rod is completely

released from the cutting dice.

MAINTENANCE

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before attempting to perform inspection or

maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

Replacing the cutting dice

NOTICE: Replace the both cutting dice at the

same time. Replacing the one side of the cutting die

may generate burr on the threaded rod.

Replace the cutting dice when it is chipped, deformed,

or the cutting gets dull. To replace, follow the instruc-

tions in "Installing the cutting dice".

► Fig.23: 1. Chipping 2. Deformation

One cutting die has two cutting edges and thick side

and thin side. Switch the installation positions of the

cutting dice if you have not used the other sides of the

cutting edges.

► Fig.24: 1. Cutting edge 2. Thin side 3. Thick side

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DSC102 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info