Bedienungsanleitung Makita DSC251 (Seite 12 von 26) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691890

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

12 ENGLISH

OPERATING

PROCEDURE

WARNING: Before the battery is inserted into

the tool, ensure that the Switch is at the “O” posi-

tion and the Switch is off.

CAUTION: Push the Lock Button and ensure

that the Button comes up when it is released.

If the Lock Button will not come up when it is

released, the Tipped Saw will be prevented from

rotating when the tool is operated resulting in

damage to parts and the motor to burn out.

CAUTION: Slide the Switch to the “l” posi-

tion and ensure it stays there and does not move.

Then push down on the rear of the Switch to

ensure that the Switch moves to the “O” position

automatically.

CAUTION: Ensure that the bolts retaining the

Tipped Saw Cover and all other bolts are tight-

ened rmly.

► Fig.5: 1. Handle Position (parallel / left side) 2. Lock

Button 3. Handle Position (parallel / right

side) 4. Switch 5. Handle Position (vertical /

upper side)

Operation

► Fig.6: 1. Guide 2. Rebar

► Fig.7: 1. Rebar 2. Guide

1. Screw the Handle into threaded hole at the vertical

or parallel position for easier operation.

2. Ensure that the Switch is at “O” position.

CAUTION: As a safety function of this tool,

the Motor cannot be energised when the battery is

inserted with the Switch at “l” position. For fur-

ther safety, please note that the battery should be

inserted with the Switch at “O” position.

3. Insert the battery into the tool.

4. Slide the Switch to “l” position. The motor is on.

Then push down on the forward end of the Switch to

lock it for operating continuously.

WARNING: Do not touch the rotating parts as

they can cause serious injury.

5. Position the Guide in the opening against the

rebar.

Then push the tool forward slowly to start to cut

the rebar.

CAUTION: When cutting, both at the begin-

ning and near the end, slow down the tool’s for-

ward (cutting) movement. A fast cutting action, at

these times, will damage the Tipped Saw blades

and can cause injury from ying debris.

CAUTION: Hold the tool rmly so that it does

not shake when cutting. Cutting with the tool

shaking will shorten the life of the Tipped Saw and

damage the blades.

CAUTION: Position the tool so it is at 90

degrees to rebar to be cut. If the tool is not at 90

degrees to the rebar, it can cause shaking and

overload the tool.

CAUTION: Do not start cutting immediately

after the motor is switched on. Allow the Tipped

Saw to reach full speed before beginning to cut.

CAUTION: Do not remove the battery when

the motor is switched on. Doing so can cause

damage to the motor’s electronics.

6. After nishing the cut, push down on the rear end

of the Switch which will cause the Switch to move to the

“O” position and turn off the motor.

CAUTION: This tool is designed to cut rebar.

Please contact the manufacturer or your local

dealer if you want to cut other materials. Cutting

other materials will damage the Tipped Saw

blades.

Caution when cutting

1. Ensure that the Tipped Saw blade is well away

from the material to be cut before switching on.

2. Slow down the forward (cutting) movement of the

tool when approaching the end of the cut. This is espe-

cially important when the piece to be cut is less than 50

mm in length. The piece cut off can strike the Tipped

Saw blades, damaging them and cause serious injury.

3. When the Tipped Saw blades become blunt or

chipped. replace the blade. Continuing to use it in this

condition will overload the tool.

4. If the material moves or shakes, when being cut,

stop the operation and properly secure the material.

5. Do not hold by hand the material to be cut. Doing

so may result in personal injury.

6. Do not cut rebar that in size or hardness exceeds

the cutting capacity of the tool.

Replace the Tipped Saw when any

of the below occurs

1. Warning Lamp (red) blinks frequently even though

the battery is fully charged.

2. The Tipped Saw blades are chipped or worn.

3. The cutting speed is very slow.

4. The surface of the cut piece is discolored by heat.

NOTE: Tipped Saw blades cannot be resharpened.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DSC251 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info