Bedienungsanleitung Makita DTD154ZJ (Seite 7 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

711188

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

7 ENGLISH

Switch action

►Fig.4: 1. Switch trigger

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

Tostartthetool,simplypulltheswitchtrigger.Tool

speedisincreasedbyincreasingpressureontheswitch

trigger. Release the switch trigger to stop.

NOTE:Thetoolautomaticallystopsifyoukeeppull-

ing the switch trigger for about 6 minutes.

Lighting up the front lamp

CAUTION: Do not look in the light or see the

source of light directly.

►Fig.5: 1. Lamp

►Fig.6: 1. Button

Pull the switch trigger to turn on the lamp. To turn off,

releaseit.Thelampgoesoutapproximately10seconds

after releasing the switch trigger.

To keep the lamp off, turn off the lamp status. First pull

and release the switch trigger. And then press the but-

ton

for one second within 10 seconds.

To turn on the lamp status again, press the button again

similarly.

NOTE:

Toconrmthelampstatus,pullthetrigger.Whenthe

lamplightsupbypullingtheswitchtrigger,thelampstatusis

ON. When the lamp does not come on, the lamp status is OFF.

NOTE:Whenthetoolisoverheated,thelightashes

foroneminute,andthentheLEDdisplaygoesoff.In

this case, cool down the tool before operating again.

NOTE:Useadryclothtowipethedirtoffthelensof

the lamp. Be careful not to scratch the lens of lamp, or

itmaylowertheillumination.

Reversing switch action

►Fig.7: 1. Reversing switch lever

CAUTION: Always check the direction of

rotation before operation.

CAUTION:

Use the reversing switch only after the

tool comes to a complete stop. Changing the direction of

rotationbeforethetoolstopsmaydamagethetool.

CAUTION:

When not operating the tool, always set the

reversing switch lever to the neutral position.

This tool has a reversing switch to change the direction of rota-

tion. Depress the reversing switch lever from the A side for clock-

wise rotation or from the B side for counterclockwise rotation.

When the reversing switch lever is in the neutral posi-

tion, the switch trigger cannot be pulled.

Changing the impact force

►Fig.8: 1. Changed in four steps 2. Hard 3. Medium

4. Soft 5. T mode 6. Button

You can change the impact force in four steps: hard, medium, soft, and T mode.

This allows a tightening suitable to the work.

Everytimethebutton

is pressed, the number of blows changes in four steps.

“T” is a special mode for fastening self drilling screws. In this mode, the tool starts to drive a screw with faster rotation, which is suited for drilling

with the self-drilling-screw tip. Once the tool starts to tighten the screw, it impacts in medium force grade.

Forapproximatelyoneminuteafterreleasingtheswitchtrigger,theimpactforcecanbechanged.

Impact force grade displayed

on panel

Maximum blows Purpose Example of application

Hard

3,800 min

-1

(/min) Tightening when force and

speed are desired.

Tightening underwork mate-

rials, tightening long screws,

tightening bolts.

Medium

2,600 min

-1

(/min) Tighteningwhenagoodnish-

ing is needed.

Tighteningnishingboards,

plaster boards.

Soft

1,100 min

-1

(/min) Tightening with less force to

avoid screw thread breakage.

Tightening sash screws, tight-

ening small screws such as M6.

T mode

2,600 min

-1

(/min) Tightening when speed and

goodnishingareneeded.

Tightening self drilling screws.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DTD154ZJ Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info