Bedienungsanleitung Makita DTD154ZJ (Seite 8 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

711188

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

8 ENGLISH

NOTE:Whenalllampsontheswitchpanelgoout,thetoolisturnedofftosavethebatterypower.Theimpactforce

gradecanbecheckedbypullingtheswitchtriggertotheextentthatthetooldoesnotoperate.

NOTE: While pulling the switch trigger, the impact force grade cannot be changed.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing driver bit/

socket bit

►Fig.9

Useonlydriverbit/socketbitthathasinsertingportion

showninthegure.Donotuseanyotherdriverbit/

socket bit.

For tool with shallow driver bit hole

A=12mm

B=9mm

Useonlythesetypeofdriver

bit. Follow the procedure

1.(Note)Bit-pieceisnot

necessary.

For tool with deep driver bit hole

A=17mm

B=14mm

Toinstallthesetypesofdriver

bits, follow the procedure 1.

A=12mm

B=9mm

Toinstallthesetypesofdriver

bits, follow the procedure 2.

(Note)Bit-pieceisnecessary

for installing the bit.

Procedure 1

For tool without one-touch type sleeve

►Fig.10: 1. Driver bit 2. Sleeve

To install the driver bit, pull the sleeve in the direction of

the arrow and insert the driver bit into the sleeve as far

as it will go.

Then release the sleeve to secure the driver bit.

For tool with one-touch type sleeve

To install the driver bit, insert the driver bit into the

sleeve as far as it will go.

Procedure 2

In addition to Procedure 1, insert the bit-piece into the

sleeve with its pointed end facing in.

►Fig.11: 1. Driver bit 2. Bit-piece 3. Sleeve

To remove the driver bit, pull the sleeve in the direction

of the arrow and pull the driver bit out.

NOTE: If the driver bit is not inserted deep enough

into the sleeve, the sleeve will not return to its original

position and the driver bit will not be secured. In this

case,tryre-insertingthebitaccordingtotheinstruc-

tions above.

NOTE:Whenitisdifculttoinsertthedriverbit,pull

the sleeve and insert it into the sleeve as far as it will

go.

NOTE: After inserting the driver bit, make sure that it

isrmlysecured.Ifitcomesout,donotuseit.

Installing hook

CAUTION: When installing the hook, always

secure it with the screw rmly. If not, the hook

maycomeofffromthetoolandresultinthepersonal

injury.

►Fig.12: 1. Groove 2. Hook 3. Screw

Thehookisconvenientfortemporarilyhangingthetool.

This can be installed on either side of the tool. To install

the hook, insert it into a groove in the tool housing on

either side and then secure it with a screw. To remove,

loosen the screw and then take it out.

OPERATION

►Fig.13

Theproperfasteningtorquemaydifferdependingupon

thekindorsizeofthescrew/bolt,thematerialofthe

workpiece to be fastened, etc. The relation between fas-

teningtorqueandfasteningtimeisshowninthegures.

Proper fastening torque for standard bolt

N•m

(kgf•cm)

M14

M12

M10

M16

M14

M12

M10

M16

140

(1428)

(1224)

(1020)

(816)

(612)

(408)

(204)

120

100

1.Fasteningtime(second)2. Fastening torque

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DTD154ZJ Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info