Bedienungsanleitung Makita DTD170 (Seite 6 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

657996

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

6 ENGLISH

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge. Failure to hold the tool and the battery

cartridgermlymaycausethemtoslipoffyourhands

and result in damage to the tool and battery cartridge

andapersonalinjury.

►Fig.1: 1. Red indicator 2. Button 3. Battery cartridge

To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator on the

upper side of the button, it is not locked completely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

itmayaccidentallyfalloutofthetool,causinginjuryto

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

Tool / battery protection system

Thetoolisequippedwithatool/batteryprotectionsys-

tem. This system automatically cuts off power to the

motor to extend tool and battery life. The tool will auto-

matically stop during operation if the tool or battery is

placedunderoneofthefollowingconditions:

Overload protection

Whenthebatteryisoperatedinamannerthatcauses

it to draw an abnormally high current, the tool automat-

ically stops without any indication. In this situation, turn

the tool off and stop the application that caused the tool

to become overloaded. Then turn the tool on to restart.

Overheat protection

Whenthebatteryisoverheated,thetoolstopsautomat-

ically. In this situation, let the battery cool before turning

the tool on again.

Overdischarge protection

Whenthebatterycapacityisnotenough,thetoolstops

automatically. In this case, remove the battery from the

tool and charge the battery.

NOTE: Overload protection will work only with batter-

ies with star marking.

►Fig.2: 1. Star marking

Indicating the remaining battery

capacity

►Fig.3: 1. Battery indicator

Whenyoupulltheswitchtrigger,theLEDdisplayshows

the remaining battery capacity. The remaining battery

capacity is shown as the following table.

Battery indicator status Remaining

battery

capacity

On Off Blinking

50% to 100%

20% to 50%

0% to 20%

Charge the

battery

NOTE:WhentheLEDdisplaygoesoff,thetoolis

turned off to save the battery power. To check the

remaining battery capacity, slightly pull the switch

trigger.

NOTE:TheLEDdisplaygoesoffapproximatelyone

minute after releasing the switch trigger.

NOTE:WhentheLEDdisplaylightsupandthetool

stops even with a recharged battery cartridge, cool

down the tool fully. If the status will not change, stop

using and have the tool repaired by a Makita local

service center.

NOTE:Whenthetoolisoverheated,thelightblinks

for one minute as shown in the table below, and then

theLEDdisplaygoesoff.Inthiscase,cooldownthe

tool before operating again.

Battery

indicator

On Off Blinking

Tool is overheated

Indicating the remaining battery

capacity

Only for battery cartridges with "B" at the end of the

model number

►Fig.4: 1. Indicator lamps 2. Check button

Pressthecheckbuttononthebatterycartridgetoindi-

cate the remaining battery capacity. The indicator lamps

light up for few seconds.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DTD170 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info