Bedienungsanleitung Makita DTD170 (Seite 8 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

657996

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

8 ENGLISH

Impact force grade displayed

on panel

Maximum blows Purpose Example of application

Max

3,800 min

-1

(/min) Tightening with the maximum

force and speed.

Tightening underwork mate-

rials, tightening long screws,

tightening bolts.

Hard

3,600 min

-1

(/min) Tightening with less force and

speed than Max mode (easier

to control than Max mode).

Tightening underwork mate-

rials, tightening long screws,

tightening bolts.

Medium

2,600 min

-1

(/min) Tighteningwhenagoodnish-

ing is needed.

Tighteningnishingboards,

plaster boards.

Soft

1,100 min

-1

(/min) Tightening with less force to

avoid screw thread breakage.

Tightening sash screws, tight-

ening small screws such as M6.

T mode

2,600 min

-1

(/min) Tightening when speed and

goodnishingareneeded.

Tightening self drilling screws.

Amode

3,800 min

-1

(/min) Tightening screws with better

control.

Tightening long screws.

NOTE:TmodeandAmodeisavailableonlywhenthetoolrotatesclockwise.WhenrotatingcounterclockwiseinT

modeandAmode,theimpactforceandspeedarethesameasmaxmode.

NOTE:Whenalllampsontheswitchpanelgoout,thetoolisturnedofftosavethebatterypower.Theimpactforce

grade can be checked by pulling the switch trigger to the extent that the tool does not operate.

NOTE:Whilepullingtheswitchtrigger,theimpactforcegradecannotbechanged.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing driver bit/

socket bit

►Fig.11

Useonlydriverbit/socketbitthathasinsertingportion

showninthegure.Donotuseanyotherdriverbit/

socket bit.

For tool with shallow driver bit hole

A=12mm

B=9mm

Use only these type of driver

bit. Follow the procedure

1. (Note) Bit-piece is not

necessary.

For tool with deep driver bit hole

A=17mm

B=14mm

To install these types of driver

bits, follow the procedure 1.

A=12mm

B=9mm

To install these types of driver

bits, follow the procedure 2.

(Note) Bit-piece is necessary

for installing the bit.

Procedure 1

For tool without one-touch type sleeve

►Fig.12: 1. Driver bit 2. Sleeve

To install the driver bit, pull the sleeve in the direction of

the arrow and insert the driver bit into the sleeve as far

as it will go.

Then release the sleeve to secure the driver bit.

For tool with one-touch type sleeve

To install the driver bit, insert the driver bit into the

sleeve as far as it will go.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DTD170 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info