Bedienungsanleitung Makita DTD170 (Seite 9 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

657996

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

9 ENGLISH

Procedure 2

In addition to Procedure 1, insert the bit-piece into the

sleeve with its pointed end facing in.

►Fig.13: 1. Driver bit 2. Bit-piece 3. Sleeve

To remove the driver bit, pull the sleeve in the direction

of the arrow and pull the driver bit out.

NOTE: If the driver bit is not inserted deep enough

into the sleeve, the sleeve will not return to its original

position and the driver bit will not be secured. In this

case, try re-inserting the bit according to the instruc-

tions above.

NOTE:Whenitisdifculttoinsertthedriverbit,pull

the sleeve and insert it into the sleeve as far as it will

go.

NOTE:Afterinsertingthedriverbit,makesurethatit

isrmlysecured.Ifitcomesout,donotuseit.

Installing hook

►Fig.14: 1. Groove 2. Hook 3. Screw

The hook is convenient for temporarily hanging the tool.

This can be installed on either side of the tool. To install

the hook, insert it into a groove in the tool housing on

either side and then secure it with a screw. To remove,

loosen the screw and then take it out.

OPERATION

►Fig.15

The proper fastening torque may differ depending upon

thekindorsizeofthescrew/bolt,thematerialofthe

workpiece to be fastened, etc. The relation between fas-

teningtorqueandfasteningtimeisshowninthegures.

Proper fastening torque for standard bolt

N•m

(kgf•cm)

M14

M12

M10

M16

M14

M12

M10

M16

140

(1428)

(1224)

(1020)

(816)

(612)

(408)

(204)

120

100

1. Fastening time (second) 2. Fastening torque

Proper fastening torque for high tensile bolt

M14

M12

M14

M12

M10

200

180

160

140

120

100

0123

(2040)

(1836)

(1632)

(1428)

(1224)

(1020)

(816)

(612)

(408)

(204)

N•m

(kgf•cm)

1. Fastening time (second) 2. Fastening torque

Holdthetoolrmlyandplacethepointofthedriverbit

inthescrewhead.Applyforwardpressuretothetoolto

the extent that the bit will not slip off the screw and turn

the tool on to start operation.

NOTICE: If you use a spare battery to continue

the operation, rest the tool at least 15 min.

NOTE:Usetheproperbitfortheheadofthescrew/

bolt that you wish to use.

NOTE:WhenfasteningM8orsmallerscrew,carefully

adjustpressureontheswitchtriggersothatthescrew

is not damaged.

NOTE: Hold the tool pointed straight at the screw.

NOTE: If the impact force is too strong or you tighten

thescrewforatimelongerthanshowninthegures,

the screw or the point of the driver bit may be over-

stressed, stripped, damaged, etc. Before starting your

job,alwaysperformatestoperationtodeterminethe

proper fastening time for your screw.

The fastening torque is affected by a wide variety of

factorsincludingthefollowing.Afterfastening,always

check the torque with a torque wrench.

1. Whenthebatterycartridgeisdischargedalmost

completely, voltage will drop and the fastening

torque will be reduced.

2. Driver bit or socket bit

Failure to use the correct size driver bit or socket

bit will cause a reduction in the fastening torque.

3. Bolt

• Eventhoughthetorquecoefcientandthe

class of bolt are the same, the proper fasten-

ing torque will differ according to the diame-

ter of bolt.

• Eventhoughthediametersofboltsarethe

same, the proper fastening torque will differ

accordingtothetorquecoefcient,theclass

of bolt and the bolt length.

4. The manner of holding the tool or the material

of driving position to be fastened will affect the

torque.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DTD170 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info