Bedienungsanleitung Makita DTD171 (Seite 11 von 22) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691706

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

11 ENGLISH

Press and hold the button and the quick

mode-switching button at the same time until the custom-

ize lamp and the lamp of desired application mode blinks.

► Fig.11:

1. Quick mode-switching button 2. Customize lamp

NOTE:

You can overwrite the current application mode

with new one by performing the procedure above.

Using the quick mode-switching function

When the tool is in the mode that is not registered, press the

quick mode-switching button to switch to the registered applica-

tion mode. The tool switches between the registered application

mode and last application mode every time you press the quick

mode-switching button. The front lamps on both sides will ash

once when switching to the registered application mode.

NOTE: The customize lamp will light up when the

application mode registered to the tool is chose.

Cancelling the quick mode-switching function

Press and hold the button and quick mode-switch-

ing button at the same time until the customize lamp

and all impact force grade lamps blink.

NOTE

: After cancelling the quick mode-switching function, the

quick mode-switching button works for changing the impact force.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing driver bit/socket bit

► Fig.12

Use only driver bit/socket bit that has inserting portion shown

in the gure. Do not use any other driver bit/socket bit.

For tool with shallow driver bit hole

A=12mm

B=9mm

Use only these type of driver bit.

Follow the procedure 1. (Note)

Bit-piece is not necessary.

For tool with deep driver bit hole

A=17mm

B=14mm

To install these types of driver

bits, follow the procedure 1.

A=12mm

B=9mm

To install these types of driver

bits, follow the procedure 2.

(Note) Bit-piece is necessary

for installing the bit.

Procedure 1

For tool without one-touch type sleeve

► Fig.13: 1. Driver bit 2. Sleeve

To install the driver bit, pull the sleeve in the direction of the

arrow and insert the driver bit into the sleeve as far as it will go.

Then release the sleeve to secure the driver bit.

For tool with one-touch type sleeve

To install the driver bit, insert the driver bit into the

sleeve as far as it will go.

Procedure 2

In addition to Procedure 1, insert the bit-piece into the

sleeve with its pointed end facing in.

► Fig.14: 1. Driver bit 2. Bit-piece 3. Sleeve

To remove the driver bit, pull the sleeve in the direction

of the arrow and pull the driver bit out.

NOTE:

If the driver bit is not inserted deep enough into

the sleeve, the sleeve will not return to its original posi-

tion and the driver bit will not be secured. In this case, try

re-inserting the bit according to the instructions above.

NOTE:

When it is difcult to insert the driver bit, pull the

sleeve and insert it into the sleeve as far as it will go.

NOTE: After inserting the driver bit, make sure that it

is rmly secured. If it comes out, do not use it.

Installing hook

CAUTION:

When installing the hook, always

secure it with the screw rmly. If not, the hook may

come off from the tool and result in the personal injury.

► Fig.15: 1. Groove 2. Hook 3. Screw

The hook is convenient for temporarily hanging the tool.

This can be installed on either side of the tool. To install

the hook, insert it into a groove in the tool housing on

either side and then secure it with a screw. To remove,

loosen the screw and then take it out.

OPERATION

► Fig.16

The proper fastening torque may differ depending upon

the kind or size of the screw/bolt, the material of the

workpiece to be fastened, etc. The relation between fas-

tening torque and fastening time is shown in the gures.

Proper fastening torque for standard bolt

N•m

(kgf•cm)

M14

M12

M10

M16

M14

M12

M10

M16

140

(1428)

(1224)

(1020)

(816)

(612)

(408)

(204)

120

100

1. Fastening time (second) 2. Fastening torque

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DTD171 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info