Bedienungsanleitung Makita DTR180 (Seite 12 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691779

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

12 ENGLISH

5. Wear clothes that have close-tting hemlines

and sleeves. Do not work with a towel or other

object wrapped around your neck. Otherwise,

they may get caught in the rotating part and cause

an accident.

6. Be sure to inspect the following points before

using the tool.

• Check that no parts are damaged

• Check that no bolts are loose

• Check that safety devices operate

normally

7. If any abnormalities are found, stop using the

tool immediately. Do not repair the tool by

yourself. Ask your local Makita Service Center

for repairs. If the tool is used in an incomplete

state, an accident may occur.

8. When installing the battery cartridge, be sure

to lock the trigger and do not place your nger

on the trigger. Incorrect operation may cause an

accident.

9. When tying rebars, exercise care not to move

them. If rebars move due to tying, you may be

injured.

10. Do not touch the wires during the wire tying

process. Otherwise, you may get caught in the

wireandinjured.

11. Do not bring your hands close to the tying

point during the wire tying process. Otherwise,

youmaygetcaughtinthewireandinjured.

12. Hold the grip of the tool rmly during the wire

tying process. Otherwise, your wrist may be

twisted or your body may be pulled, which may

resultinaninjury.

13. Do not move to the next tying point until the

current wire tying process is completed.

Otherwise,youmaybeinjured.

14. Pay attention to the end of the wire during the

wire tying process. Otherwise, your hand may

be caught by the end of the wire, and you may be

injured.

15. Do not touch the contact plate during the wire

tying process. If you need to touch the contact

plate, be sure to lock the trigger, or turn the

power switch off and remove the battery car-

tridge.Otherwise,youmaybeinjured.

16. When you have completed the wire tying pro-

cess, pull the tool up vertically. Otherwise, the

arm may be caught on rebars, which may cause

an accident.

17. Be careful not to drop, bump, or hit the tool.

If a strong impact is applied prior to the tool

being used, make sure that the tool is not dam-

aged or cracked, and that the safety devices

operate normally. Otherwise, an accident may

occur.

18. If any of the following phenomena occur, lock

the trigger, turn the power switch off, and

remove the battery cartridge from the tool.

If the tool operates incorrectly, an accident may

occur.

• If an operating sound is heard as soon as

the battery cartridge is mounted.

• If overheating or abnormal smells or

noises are detected.

• When you are taking measures in

response to the error display. (Ask your

local Makita Service Center for repairs.)

• When loading or unloading a wire reel.

• When you move while holding the tool

during work.

• When you do not use the tool.

• When you inspect or adjust the tool.

• When you remove a stranded wire.

19. When working on scaffolding, always stabilize

it and work using a posture that will ensure

you maintain your balance. If scaffolding is

unstable, an accident may occur.

20. When working on a roof or similar locations,

move in a forward direction while working so

that you can see where you are going. If you

move in a backward direction while working, you

may lose your footing and cause an accident.

21. If you are working in a highly elevated loca-

tion, ensure that no one is below you, and pay

attention to ensure you do not drop any tools

while working. Dropping the tool may cause an

accident.

22. Do not use the tool for any work other than

wire tying. Otherwise, an accident may occur.

23. Always use Makita's genuine wires. If wires are

not used for a long period of time, they may

rust. Do not use rusted wires. Otherwise, they

may cause an accident.

24. After tying, check for wire breakage due to

excessive twisting. If any wires are broken,

tying strength will be lost. Adjust the tying

strength, and tie the rebars again.

25. Securely place the arm against the rebars. If

it is not securely positioned, a clearance will be

created between the rebars, and tying strength will

be compromised.

Important safety instructions for

battery cartridge

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using

battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DTR180 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info