Bedienungsanleitung Makita DTR180 (Seite 14 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691779

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

14 ENGLISH

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may differ slightly

from the actual capacity.

Tool / battery protection system

The tool is equipped with a tool/battery protection sys-

tem. This system automatically cuts off power to the

motor to extend tool and battery life. The tool will auto-

matically stop during operation if the tool or battery is

placed under one of the following conditions:

Overload protection

When the battery is operated in a manner that causes

it to draw an abnormally high current, the tool auto-

matically stops and the corresponding error number is

displayed on the display panel. In this situation, turn the

tool off and stop the application that caused the tool to

become overloaded. Then turn the tool on to restart.

Overheat protection

When the tool or battery is overheated, the tool stops

automatically and the corresponding error number is

displayed on the display panel. In this case, let the tool

and battery cool before turning the tool on again.

Overdischarge protection

When the battery capacity is not enough, the tool stops

automatically and the corresponding error number is

displayed on the display panel. In this case, remove the

battery from the tool and charge the battery.

Main power switch

CAUTION: When you turn the power on, never

bring your limbs or face close to the binding or

rotating parts of the tool tip. Otherwise, you may

beinjured.

CAUTION: When the power is turned on,

never touch the binding or rotating parts of the

tool tip.Otherwise,youmaybeinjured.

CAUTION: Before inserting the battery car-

tridge, be sure to release your ngers from the

switch trigger and lock the trigger. If you insert

the battery cartridge while the switch trigger is being

pulled, it may cause an accident if the wire tying

process is accidentally carried out.

►Fig.3

When you press the power button, the power turns

on and the tying mode lamp lights up. In order for the

tooltoadjustitsinitialposition,itoperatestemporarily.

Whenadjustmenthascompleted,thetoolstopsauto-

matically. When you press the power button again, the

power turns off and the tying mode lamp goes out.

►Fig.4: 1. Tying mode lamp 2. Power button

NOTE: The tool has an auto power-off function. If the

switch trigger is not pulled for 10 minutes, the tool

is automatically turned off to reduce battery power

consumption.

NOTE: To restart the tool, turn the power on again.

Mode switching button

When the power is turned on and the tying mode lamp

is lit, you can select the single actuation mode or the

continuous actuation mode via the mode switching but-

ton. When you turn the power on again, the tool starts in

the mode that was most recently selected.

►Fig.5: 1. Mode switching button 2. Single actuation

mode 3. Continuous actuation mode

Switch action

WARNING: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

CAUTION: When not operating the tool,

depress the trigger-lock button from side to

lock the switch trigger in the OFF position.

►Fig.6: 1. Switch trigger 2. Trigger-lock button

To prevent the switch trigger from accidentally pulled,

the trigger-lock button is provided. To start the tool,

depress the trigger-lock button from A side and pull the

switch trigger. Release the switch trigger to stop. After

use, press in the trigger-lock button from B side.

When you pull the switch trigger, the tool performs the

next sequential operations as follows, and the tool stops

automatically.

1. Feed the wire.

2. Cut the wire.

3. The hook holds and twists the wire.

4. The hook returns to the original position.

Tying strength setting

CAUTION: Be sure to lock the trigger before

starting the adjustment. When you turn the power

on, never bring your limbs or face close to the

binding or rotating parts of the tool tip. Otherwise,

youmaybeinjured.

►Fig.7

Youcansetthetyingstrengthbyadjustingthetying

strengthadjustingbutton.Tyingstrengthisshownon

the display panel.

►Fig.8: 1.Tyingstrengthadjustingbutton2. Display

panel

If the wire is broken off, tying strength will be lost. After

tying, check the twisted portion for breakage.

Ifthewireisbrokenoff,adjustthetyingstrengthusingthe

tyingstrengthadjustingbutton,andtietherebarsagain.

Remaining battery notication

When the battery voltage drops below the required level,

the tool will stop operating, an error tone will sound, and

the number "4" will appear on the display panel. The error

tone will continue to sound until the power is turned off.

NOTE: If the ambient temperature is extremely low,

the error tone may sound even when the battery

containssufcientpower.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DTR180 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info