Bedienungsanleitung Makita DTR180 (Seite 15 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691779

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

15 ENGLISH

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Loading the tie wire (wire reel)

CAUTION: Before mounting or dismounting

tie wires and accessories, be sure to turn the

power off, lock the trigger, and remove the battery

cartridge. Failure to do so may cause an accident.

NOTICE: Using wires other than Makita's genu-

ine tie wires (annealed wires) may cause the tool

to malfunction.

1. Push the release lever, and lock it with the lock

lever.

►Fig.9: 1. Release lever 2. Lock lever

When you push the release lever, a gap is created

between the left and right feed gears.

►Fig.10: 1. Release lever 2. Lock lever 3. Feed gears

2. Peel off the tape that holds the wire, and pull the

tip of the wire out.

►Fig.11: 1. Tape 2. Tip of wire

3. Open the reel cover.

►Fig.12: 1. Reel cover

4. Mount the wire reel on the tool in the orientation

showninthegure.

►Fig.13: 1. Wire reel

NOTICE: Be sure to mount the wire reel in the

orientation shown in the gure. If it is mounted the

other way around, the wire will be released and may

be twisted.

5. Make the tip of the wire straight, and pass the wire

through the guide.

►Fig.14: 1. Guide

NOTE: If the tip of the wire is bent when it is passed

throughtheguide,thewiremaybecomejammedin

the tool.

NOTE: If you force the wire when trying to pass it

throughtheguide,thewiremaybecomejammed.

6. Pull the wire out approximately 10 mm from the tip

of the arm.

►Fig.15: 1. Arm 2. Approximately 10 mm

NOTICE: If the length of the pulled-out wire is

insufcient, the wire may be broken off when tied,

or tying strength may be compromised due to

insufcient wraps.

7. Remove all tape that holds the wire.

►Fig.16

8. Rewind the wire to eliminate its slack.

►Fig.17

9. Release the lock lever. The release lever returns,

and the wire is held by the left and right gears.

►Fig.18: 1. Release lever 2. Lock lever

►Fig.19: 1. Gear 2. Path of the wire 3. Wire

NOTICE: When the lock lever is released and

when the left and right gears mesh with each

other, the grooves in the gears form a space. This

space becomes the path for the wire. Make sure

that the wire is passed through this path.

10. Close the reel cover.

►Fig.20: 1. Reel cover

OPERATION

Checking before work

CAUTION: If the tool has a safety mecha-

nism-related problem, do not use it. If you continue

to use it, an accident may occur.

Before using the tool, make sure that the safety mecha-

nism operates normally. If the tool operates without the

safety mechanism operating, stop using the tool imme-

diately. Ask your local Makita Service Center for repairs.

Checking the trigger-lock

The tool has the trigger-lock to prevent the tool from

operating when you do not intend to use it. Lock the trig-

gerandconrmthattheswitchtriggercannotbepulled.

Checking the curl guide

To prevent the operator from touching the binding or

rotating parts of the tool tip by mistake, the tool will not

operate even if the switch trigger is pulled while the

curl guide is opened. When the operator releases their

ngerfromtheswitchtriggerandclosesthecurlguide,

the tool can operate.

►Fig.21: 1. Curl guide

Checkout for curl guide open/close detection

Remove the tie wire, check the tool operation according

to the following steps, and make sure that the tool does

not start if the curl guide is open.

1. Turn the power off, and leave the curl guide open.

2. Turn the power on.

If the tool will not operate and if the value "2" is shown

on the display panel, the state of the tool is normal. Turn

the power off, and close the curl guide.

If the tool operates and if no error is shown on the dis-

play panel, the state of the tool is abnormal. Stop using

the tool immediately, and ask your local Makita Service

Center for repairs.

CAUTION: If you open the curl guide and turn

the power on to check the interlock, hold the curl

guide as shown in the gure. Never bring your

limbs or face close to the binding or rotating parts

of the tool tip.Otherwise,youmaybeinjured.

►Fig.22

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DTR180 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info